blob: 94e83a49cf9a25a01207d4febfa4bd8007958aef (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
|
substitutions:
name: kauf-plug # **** CHANGE DEVICE NAME TO SOMETHING UNIQUE PER DEVICE. RENAME YAML FILE TO SAME NAME. ****
# **** USE DASHES (-) INSTEAD OF SPACES OR UNDERSCORE (_). USE ONLY LOWER CASE LETTERS. ****
friendly_name: Kauf Plug # **** CHANGE FRIENDLY NAME TO SOMETHING UNIQUE PER DEVICE ****
esphome:
name: $name
platform: ESP8266
board: esp01_1m
esp8266_restore_from_flash: true
project:
name: "Kauf.PLF10"
version: "1.97(m)"
wifi:
# **** ENTER WI-FI CREDENTIALS HERE, USING SECRETS.YAML RECOMMENDED ****
ssid: initial_ap # !secret my_wifi_ssid
password: asdfasdfasdfasdf # !secret my_wifi_pass
# Uncomment below to set a static IP
# manual_ip:
# static_ip: !secret kauf_bulb_ip_address
# gateway: !secret wifi_gateway
# subnet: !secret wifi_subnet
# dns1: !secret wifi_dns1
# use_address allows wireless programming through the ESPHome dashboard.
# Set to the plug's IP Address. Remove after programming.
# use_address: 192.168.1.3
# default is 20, 17 is recommended.
output_power: 17
# using fast_connect as default since it is required for hidden networks.
# feel free to change or override.
fast_connect: true
logger: # Enable logging
# baud_rate: 0 # Disable UART logging since TX pad not easily available
api: # Enable Home Assistant API
# password: !secret api_password # optional password field for Home Assistant API.
ota:
# password: !secret ota_password # optional password for OTA updates.
# red led, blink when not connected to wifi or Home Assistant
status_led:
pin:
number: GPIO0
inverted: true
binary_sensor:
# button input toggles relay and thereby blue led
- platform: gpio
id: button
name: Kauf Plug Button
pin:
number: GPIO13
mode:
input: true
pullup: true
inverted: true
filters:
- delayed_on: 100ms
on_press:
then:
switch.toggle: relay
switch:
# blue LED follows relay power state
- platform: gpio
id: blue_led
pin:
number: GPIO2
inverted: true
# relay output
- platform: gpio
id: relay
name: $friendly_name
pin: GPIO4
# automatically make blue led equal relay state
on_turn_on:
- switch.turn_on: blue_led
on_turn_off:
- switch.turn_off: blue_led
# clock input from Home Assistant used to calculate total daily energy
time:
- platform: homeassistant
id: homeassistant_time
sensor: # Power monitoring sensors output to Home Assistant
- platform: hlw8012
sel_pin:
number: GPIO12
inverted: True
cf_pin: GPIO5
cf1_pin: GPIO14
current_resistor: 0.001 # The value of the shunt resistor for current measurement.
voltage_divider: 2401 # The value of the voltage divider on the board as (R_upstream + R_downstream) / R_downstream.
power:
name: ${friendly_name} Power
unit_of_measurement: W
id: wattage
filters:
- calibrate_linear:
- 0.0 -> 0.0
- 333.8 -> 60 # value with 60W bulb.
current:
name: ${friendly_name} Current
unit_of_measurement: A
filters:
- calibrate_linear:
- 0.0 -> 0.0
- 0.6 -> 0.515 # value with 60W bulb.
voltage:
name: ${friendly_name} Voltage
unit_of_measurement: V
filters:
- calibrate_linear:
- 0.0 -> 0.0
- 302.1 -> 117.1 # Tested using a meter
change_mode_every: 1
update_interval: 10s # 20 second effective update rate for Power, 40 second for Current and Voltage.
# Reports the total Power so-far each day, resets at midnight
# See https://esphome.io/components/sensor/total_daily_energy.html
- platform: total_daily_energy
name: ${friendly_name} Total Daily Energy
power_id: wattage
filters:
- multiply: 0.001 ## convert Wh to kWh
unit_of_measurement: kWh
|
