Pinecil V2 (#1341)

* Add SDK

* fork

* massaging makefile

* Drop git module

* Bring in sdk as its broken

Far, Far to much crap to fix with regex now

* Remove bl706

* rf_para_flash_t is missing defs

* Remove crapton of junk

* Remove yet more

* Poking I2C

* Update peripheral_config.h

* Update pinmux_config.h

* Update preRTOS.cpp

* Update main.hpp

* Setup template

* Verbose boot

* I2C ish

* Update I2C_Wrapper.cpp

* Update main.cpp

* Turn off I2C reading for now

* Display running

* Roughing out scheduling timer0

* Starting ADC setup

* Working scheduling of ADC :tada:

* Format adc headers

* Update IRQ.cpp

* Buttons working

* Slow down I2C

* Poking IRQ

* Larger stack required

* Accel on

* Trying to chase down why __libc_init_array isnt working yet

* Working c++

* Cleanup

* Bump stacks

* I2C wake part workaround

* Cleanup

* Working PWM init

* qc draft

* Hookup PWM

* Stable enough ADC

* ADC timing faster + timer without HAL

* Silence

* Remove boot banner

* Tuning in ADC

* Wake PID after ADC

* Remove unused hal

* Draft flash settings

* Working settings save & restore

* Update to prod model

* Cleanup

* NTC thermistor

* Correct adc gain

* Rough tip resistance progress

* Scratch out resistance awareness of the tip

* better adc settings

* Tweaking ADC

* ADC tweaking

* Make adc range scalable

* Update Dockerfile

* Update configuration.h

* Can read same ADC twice in a row

* ADC Setup

* Update PIDThread.cpp

* Lesser adc backoff

* Update USBPD.h

* Add device ID

* Update BSP_Power.h

* Update BSP.cpp

* DrawHex dynamicLength

* Shorter ID padding

* Show validation code

* tip measurement

* Create access for w0w1

* Expose w0 w1

* Enable debug

* crc32

* Device validation

* wip starting epr

* Logic refactor

* Safer PWM Init

* PD cleanups

* Update bl702_pwm.c

* Update power.cpp

* Update usb-pd

* io

* EPR decode

* Better gui for showing pd specs

* Rough handler for capabilities

* EPR

* Fix > 25V input

* Perform pow step after PPS

* Update BSP.cpp

* Fix timer output

* QC3

* Add tip resistance view

* Hold PD negotiation until detection is done for tip res

* Get Thermal mass

* Tip res =0 protection

* Update PIDThread.cpp

* Update GUIThread.cpp

* Rewrite tip resistance measurement

* Update GUIThread.cpp

* Fix fallback

* Far better tip resistance measurement

* Fix QC 0.6V D-

* Convert the interpolator to int32

* Correct the NTC lookup

* Update BSP.cpp

* Update Setup.cpp

* .

Update configuration #defines

More backported functions

* Update usb-pd

* More missed updates

* Refactor BSP

Magic BSP -> PinecilV2
Pine64 BSP -> Pinecil

Update Makefile

* Add Pinecilv2 to CI

* Pinecil v2 multi-lang

Update push.yml

* Update HallSensor.md

* Update README.md

* Fix wrong prestartcheck default

* Fix logo mapping

* Update Makefile

* Remove unused font block

* Style

* Style

* Remove unused timer funcs

* More culling TS80P

* Revert "More culling TS80P"

This reverts commit 2078b89be7fb244144c4494856f355445e3f8b92.

* Revert "Remove unused timer funcs"

This reverts commit 0c693a89cc187588ba3525c6b55a656c42781f19.

* Make VBus check maskable

* Remove DMA half transfer

* Drop using brightness and invert icons and go back to text

Saves flash space

* Refactor settings UI drawing descriptions

* Shorten setting function names

* Store bin file assets

* Fix MHP prestart

1 files changed, 14 insertions, 18 deletions

diff --git a/README.md b/README.md
index eae65460..506bc213 100644
--- a/README.md
+++ b/README.md
@@ -20,22 +20,17 @@ This project is considered feature complete for use as a soldering iron, _so ple
 
 _This firmware does **NOT** support the USB port while running for changing settings. This is done through the onscreen menu only. Logos are edited using the tool or python script and uploaded in DFU mode._
 
-
-
-|   Device  | DC | QC | PD | EPR | BLE | Battery | Recommended |
-|----------:|:--:|:--:|:--:|:---:|:---:|:-------:|:-----------:|
-|     MHP30 |❌ | ❌ | ✔️ | ❌ | ❌ |   ❌    |     ✔️     |
-|   Pinecil |✔️ | ✔️ | ✔️ | ❌ | ❌ |   ✔️    |     ✔️     |
-| Pinecil 2 |✔️ | ✔️ | ✔️ | ✔️ | ✔️ |   ✔️    |     ✔️     |
-|     TS100 |✔️ | ❌ | ❌ | ❌ | ❌ |   ✔️    |     ❌     |
-|      TS80 |❌ | ✔️ | ❌ | ❌ | ❌ |   ✔️    |     ❌     |
-|     TS80P |❌ | ✔️ | ✔️ | ❌ | ❌ |   ✔️    |     ✔️     |
-
-
+|    Device | DC  | QC  | PD  | EPR | BLE | Battery | Recommended |
+| --------: | :-: | :-: | :-: | :-: | :-: | :-----: | :---------: |
+|     MHP30 | ❌  | ❌  | ✔️  | ❌  | ❌  |   ❌    |     ✔️      |
+|   Pinecil | ✔️  | ✔️  | ✔️  | ❌  | ❌  |   ✔️    |     ✔️      |
+| Pinecil 2 | ✔️  | ✔️  | ✔️  | ✔️  | ✔️  |   ✔️    |     ✔️      |
+|     TS100 | ✔️  | ❌  | ❌  | ❌  | ❌  |   ✔️    |     ❌      |
+|      TS80 | ❌  | ✔️  | ❌  | ❌  | ❌  |   ✔️    |     ❌      |
+|     TS80P | ❌  | ✔️  | ✔️  | ❌  | ❌  |   ✔️    |     ✔️      |
 
 Please note that Miniware started shipping TS100's using cloned STM32 Chips. While these do work with IronOS, their DFU bootloader works terribly, and it is hard to get it to successfully flash larger firmware images like IronOS without timing out. This is the main reason why the TS100 is _no longer recommended_.
 
-
 ## Getting Started
 
 To get started with IronOS firmware, please jump to [Getting Started Guide](Documentation/GettingStarted.md).
@@ -56,6 +51,7 @@ For notes on installation for your device, please refer to the [Flashing Guide](
 - (TS80) Set 18 W or 24 W settings for your power bank
 - (TS80P) Automatically negotiates appropriate PD and falls back to QC mode like TS80
 - (Pinecil) Supports all 3 power modes (PD, QC, DC In).
+- (Pinecilv2) Supports USB-PD EPR for 28V operation.
 - Improved readability Fonts, supporting multiple languages
 - Use hardware features to improve reliability
 - Can disable movement detection if desired
@@ -70,17 +66,17 @@ For notes on installation for your device, please refer to the [Flashing Guide](
 This new firmware uses a new menu system to allow access to the settings on the device.
 When on the main screen and having the tip plugged in, the unit shows a pair of prompts for the two most common operations.
 
-- Pressing the button near the tip enters the *soldering mode*
-- Pressing the button near the USB end enters the *settings menu*
-- When not in *soldering mode*, holding down the button near the tip will enter *soldering temperature adjust mode* (This is the same as the one in the *soldering mode*, but allows to adjust the temperature before heating up), in *soldering mode* however this will activate *boost mode* as long as you hold down the button.
-- Holding down the button near the USB end will show the *[debug menu](Documentation/DebugMenu.md).* In *soldering mode* this ends the heating.
+- Pressing the button near the tip enters the _soldering mode_
+- Pressing the button near the USB end enters the _settings menu_
+- When not in _soldering mode_, holding down the button near the tip will enter _soldering temperature adjust mode_ (This is the same as the one in the _soldering mode_, but allows to adjust the temperature before heating up), in _soldering mode_ however this will activate _boost mode_ as long as you hold down the button.
+- Holding down the button near the USB end will show the _[debug menu](Documentation/DebugMenu.md)._ In _soldering mode_ this ends the heating.
 
 Operation details are over in the [Menu information.](Documentation/Menu.md)
 
 ## Thanks
 
 If you love this firmware and want to continue my caffeine addiction, you can do so [here](https://paypal.me/RalimTek) (or email me for other options).
-I also want to give a shout out to all of the [Fantastic Contributors](https://github.com/Ralim/ts100/graphs/contributors).
+I also want to give a shout out to all of the [Fantastic Contributors](https://github.com/Ralim/IronOS/graphs/contributors).
 
 Especially to the following users, who have helped in various ways that are massively appreciated: