diff options
38 files changed, 127 insertions, 127 deletions
diff --git a/Documentation/GettingStarted.md b/Documentation/GettingStarted.md index 8952fd9d..cf31df52 100644 --- a/Documentation/GettingStarted.md +++ b/Documentation/GettingStarted.md @@ -42,7 +42,7 @@ This OLED screen features burn-in protection; if no buttons or movement have bee Additionally to the two icons shown, there are two "hidden" actions that can be performed on this menu. -On devices that do not support Soldering profile mode, if you press and hold the button near the tip (`+/A`), this enters the temperature adjustment screen. Normally this is not required; but if you would like to adjust the set temperature _before_ the tip starts to heat, this can be useful. +On devices that do not support profile mode, if you press and hold the button near the tip (`+/A`), this enters the temperature adjustment screen. Normally this is not required; but if you would like to adjust the set temperature _before_ the tip starts to heat, this can be useful. If you press and hold the button near the rear of the iron (`-/B`), it will take you into the [debug menu](https://ralim.github.io/IronOS/DebugMenu/). @@ -74,22 +74,22 @@ Pinecil has an unpopulated footprint (U14) for a hall effect sensor (Si7210-B-00 If, after entering sleep mode, the iron still does not see movement for a much longer time (default=10 minutes); it will shut down and return to the home screen. -## Soldering Profile Mode (MHP30 only) +## Profile Mode (MHP30 only) -On devices that support it, wehn you long press the button to enter the soldering mode, the iron will play out the configured soldering profile. In this mode, you cannot adjust the temperature as it is configured according to the soldering profile you can configure through the settings menu. +On devices that support it, when you long press the button to enter the soldering mode, you enter profile mode which will adjust the temperature according to the profile mode settings. -The soldering profile plays out as follows: +Profile mode plays out as follows: -1. Check if the temperature is below 55C. If not, you will get a warning and cannot enter soldering profile mode. +1. Check if the temperature is below 55C. If not, you will get a warning and cannot enter profile mode. 2. Preheat by raising the target temperature to the configured preheat temperature with the configured preheat speed. 3. Wait for the iron to reach the preheat temperature. 4. Gradually move the target temperature to the configured end temperature of the first phase over the configured duration. 5. Wait for the iron to reach the end temperature. 6. Repeat steps 4 and 5 for the next phases until there are no more phases configured. 7. Cool down by lowering the target temperature to 0 with the configured cooldown speed. -8. Once the temperature is below 55C, sound the buzzer (if avaialable) and exit soldering profile mode. +8. Once the temperature is below 55C, sound the buzzer (if available) and exit profile mode. -You can manually exit soldering profile mode manually in the same way as the soldering mode, by pressing and holding the rear button or pressing both buttons at once. +You can manually exit profile mode manually in the same way as the soldering mode, by pressing and holding the rear button or pressing both buttons at once. ## Settings Menu diff --git a/Documentation/Menu.md b/Documentation/Menu.md index 5424f55e..9a349da3 100644 --- a/Documentation/Menu.md +++ b/Documentation/Menu.md @@ -9,11 +9,11 @@ In this mode the iron works as you would expect, pressing either button will tak - Pressing both buttons or holding the rear button (`-/B`) will exit Soldering Mode. - Holding the front button (`+/A`) will enter [Boost mode](https://ralim.github.io/IronOS/Menu/#boost-mode) (if enabled). -## Soldering profile mode (MHP30 only) +## Profile mode (MHP30 only) -In this mode, accessible by long pressing the button that brings you into soldering mode, the iron will play out the configured soldering profile. +In this mode, accessible by long pressing the button that brings you into soldering mode, the iron will play out the configured profile. - You cannot adjust the temperature or enter boost mode. -- Pressing both buttons or holding the rear button (`-/B`) will exit Soldering Profile Mode as well. +- Pressing both buttons or holding the rear button (`-/B`) will exit Profile Mode as well. ## Settings mode diff --git a/Translations/translation_BE.json b/Translations/translation_BE.json index 9d180ebd..72ddf0f5 100644 --- a/Translations/translation_BE.json +++ b/Translations/translation_BE.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Адчувальнасць\nакселерометра", diff --git a/Translations/translation_BG.json b/Translations/translation_BG.json index e32b83f1..72b4f49f 100644 --- a/Translations/translation_BG.json +++ b/Translations/translation_BG.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Усещане\nза движение", diff --git a/Translations/translation_CS.json b/Translations/translation_CS.json index 90739a29..fb4c4d1f 100644 --- a/Translations/translation_CS.json +++ b/Translations/translation_CS.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Citlivost\nna pohyb", diff --git a/Translations/translation_DA.json b/Translations/translation_DA.json index fbdd348c..12625a67 100644 --- a/Translations/translation_DA.json +++ b/Translations/translation_DA.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Bevægelses\nfølsomhed", diff --git a/Translations/translation_DE.json b/Translations/translation_DE.json index 559301b4..d04c57c2 100644 --- a/Translations/translation_DE.json +++ b/Translations/translation_DE.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhasen", - "description": "Anzahl an Phasen für das Lötprofil" + "description": "Anzahl an Phasen im Profilmodus" }, "ProfilePreheatTemp": { "displayText": "Vorheiz-\ntemperatur", - "description": "Auf diese Temperatur vorheizen zum Start des Profils" + "description": "Zu Beginn des Profilmodus auf diese Temperatur vorheizen" }, "ProfilePreheatSpeed": { "displayText": "Vorheiz-\nrate", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Abkühl-\nrate", - "description": "Abkühlenen nach der letzten Phase mit dieser Geschwindigkeit (Grad pro Sekunde)" + "description": "Am Ende des Profilmodus mit dieser Geschwindigkeit abkühlen (Grad pro Sekunde)" }, "MotionSensitivity": { "displayText": "Bewegungs-\nempfindlichk.", diff --git a/Translations/translation_EL.json b/Translations/translation_EL.json index 2791444b..ae81203d 100644 --- a/Translations/translation_EL.json +++ b/Translations/translation_EL.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Ευαισθησία\nκίνησης", diff --git a/Translations/translation_EN.json b/Translations/translation_EN.json index 1842bd12..2c044e33 100644 --- a/Translations/translation_EN.json +++ b/Translations/translation_EN.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Motion\nsensitivity", diff --git a/Translations/translation_ES.json b/Translations/translation_ES.json index 7c17fe66..575ddf1a 100644 --- a/Translations/translation_ES.json +++ b/Translations/translation_ES.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Detección de\nmovimiento", diff --git a/Translations/translation_FI.json b/Translations/translation_FI.json index 0831af0a..9bb4e90c 100644 --- a/Translations/translation_FI.json +++ b/Translations/translation_FI.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Liikkeen\nherkkyys", diff --git a/Translations/translation_FR.json b/Translations/translation_FR.json index ea7984cb..4aca77b0 100644 --- a/Translations/translation_FR.json +++ b/Translations/translation_FR.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Sensibilité\nau mouvement", diff --git a/Translations/translation_HR.json b/Translations/translation_HR.json index 7256ef88..093e66f7 100644 --- a/Translations/translation_HR.json +++ b/Translations/translation_HR.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Osjetljivost\npokreta", diff --git a/Translations/translation_HU.json b/Translations/translation_HU.json index 74e0a0c4..449a28c3 100644 --- a/Translations/translation_HU.json +++ b/Translations/translation_HU.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Mozgás\nérzékenység", diff --git a/Translations/translation_IT.json b/Translations/translation_IT.json index f5bfea25..672061d7 100644 --- a/Translations/translation_IT.json +++ b/Translations/translation_IT.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Sensibilità\nal movimento", diff --git a/Translations/translation_JA_JP.json b/Translations/translation_JA_JP.json index 92f0fa20..f2db8ef0 100755 --- a/Translations/translation_JA_JP.json +++ b/Translations/translation_JA_JP.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "動きの感度", diff --git a/Translations/translation_LT.json b/Translations/translation_LT.json index 0dd08c10..96387be6 100644 --- a/Translations/translation_LT.json +++ b/Translations/translation_LT.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Judesio\njautrumas", diff --git a/Translations/translation_NB.json b/Translations/translation_NB.json index c0c383a0..f716171f 100644 --- a/Translations/translation_NB.json +++ b/Translations/translation_NB.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "BSensr\n", diff --git a/Translations/translation_NL.json b/Translations/translation_NL.json index f848c26b..4a1d2d56 100644 --- a/Translations/translation_NL.json +++ b/Translations/translation_NL.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Bewegings-\ngevoeligheid", diff --git a/Translations/translation_NL_BE.json b/Translations/translation_NL_BE.json index 1db72308..9d841449 100644 --- a/Translations/translation_NL_BE.json +++ b/Translations/translation_NL_BE.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Bewegings-\ngevoeligheid", diff --git a/Translations/translation_PL.json b/Translations/translation_PL.json index 312767f3..604e8e29 100644 --- a/Translations/translation_PL.json +++ b/Translations/translation_PL.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Czułość\nwykr. ruchu", diff --git a/Translations/translation_PT.json b/Translations/translation_PT.json index 22835448..47be541a 100644 --- a/Translations/translation_PT.json +++ b/Translations/translation_PT.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Sensibilidade\nmovimento", diff --git a/Translations/translation_RO.json b/Translations/translation_RO.json index bf04a3df..b40e8d16 100644 --- a/Translations/translation_RO.json +++ b/Translations/translation_RO.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Sensibilitate\nla miscare", diff --git a/Translations/translation_RU.json b/Translations/translation_RU.json index 9a2803e0..2488aaef 100644 --- a/Translations/translation_RU.json +++ b/Translations/translation_RU.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Чувствительн.\nакселерометра", diff --git a/Translations/translation_SK.json b/Translations/translation_SK.json index 8ec31214..b0b550ad 100644 --- a/Translations/translation_SK.json +++ b/Translations/translation_SK.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Citlivosť\npohybu", diff --git a/Translations/translation_SL.json b/Translations/translation_SL.json index 0cb20531..5e7d2d6d 100644 --- a/Translations/translation_SL.json +++ b/Translations/translation_SL.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Občutljivost\npremikanja", diff --git a/Translations/translation_SR_CYRL.json b/Translations/translation_SR_CYRL.json index e1b55280..35f85793 100644 --- a/Translations/translation_SR_CYRL.json +++ b/Translations/translation_SR_CYRL.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Осетљивост\nна покрет", diff --git a/Translations/translation_SR_LATN.json b/Translations/translation_SR_LATN.json index 38698ca7..6906b7be 100644 --- a/Translations/translation_SR_LATN.json +++ b/Translations/translation_SR_LATN.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Osetljivost\nna pokret", diff --git a/Translations/translation_SV.json b/Translations/translation_SV.json index 6b9ac562..58d6f6d8 100644 --- a/Translations/translation_SV.json +++ b/Translations/translation_SV.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Rörelse-\nkänslighet", diff --git a/Translations/translation_TR.json b/Translations/translation_TR.json index 36a33937..3a22cd19 100644 --- a/Translations/translation_TR.json +++ b/Translations/translation_TR.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "HARHAS\n", diff --git a/Translations/translation_UK.json b/Translations/translation_UK.json index 55dee655..4302a650 100644 --- a/Translations/translation_UK.json +++ b/Translations/translation_UK.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Чутливість\nсенсору руху", diff --git a/Translations/translation_VI.json b/Translations/translation_VI.json index d77ee97e..10c36e0b 100644 --- a/Translations/translation_VI.json +++ b/Translations/translation_VI.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "Cam bien\ncu đong", diff --git a/Translations/translation_YUE_HK.json b/Translations/translation_YUE_HK.json index 127e555d..3b990f9c 100644 --- a/Translations/translation_YUE_HK.json +++ b/Translations/translation_YUE_HK.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "動作敏感度", diff --git a/Translations/translation_ZH_CN.json b/Translations/translation_ZH_CN.json index 48da8c1d..a4c8bbb4 100644 --- a/Translations/translation_ZH_CN.json +++ b/Translations/translation_ZH_CN.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "动作灵敏度", diff --git a/Translations/translation_ZH_TW.json b/Translations/translation_ZH_TW.json index 30e9bd0c..ec0ec2e3 100644 --- a/Translations/translation_ZH_TW.json +++ b/Translations/translation_ZH_TW.json @@ -154,11 +154,11 @@ }, "ProfilePhases": { "displayText": "Profile\nPhases", - "description": "Number of phases for the soldering profile" + "description": "Number of phases in profile mode" }, "ProfilePreheatTemp": { "displayText": "Preheat\nTemp", - "description": "Preheat to this temperature when starting the profile" + "description": "Preheat to this temperature at the start of profile mode" }, "ProfilePreheatSpeed": { "displayText": "Preheat\nSpeed", @@ -206,7 +206,7 @@ }, "ProfileCooldownSpeed": { "displayText": "Cooldown\nSpeed", - "description": "Cooldown at this rate after the last phase (degrees per second)" + "description": "Cooldown at this rate at the end of profile mode (degrees per second)" }, "MotionSensitivity": { "displayText": "動作敏感度", diff --git a/Translations/translations_definitions.json b/Translations/translations_definitions.json index 2229ddf9..96d237b7 100644 --- a/Translations/translations_definitions.json +++ b/Translations/translations_definitions.json @@ -70,13 +70,13 @@ "id": "ProfilePreheatString", "maxLen": 9, "include": ["PROFILE_SUPPORT"], - "description": "Shown when the soldering profile is preheating" + "description": "Shown in profile mode while preheating" }, { "id": "ProfileCooldownString", "maxLen": 9, "include": ["PROFILE_SUPPORT"], - "description": "Shown when the soldering profile is done and cooling down" + "description": "Shown in profile mode while cooling down" }, { "id": "SleepingSimpleString", @@ -289,98 +289,98 @@ "maxLen": 6, "maxLen2": 13, "include": ["PROFILE_SUPPORT"], - "description": "set the number of phases for the soldering profile." + "description": "set the number of phases for profile mode." }, { "id": "ProfilePreheatTemp", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "For the soldering profile, preheat to this temperature before proceeding with phase 1." + "description": "Preheat to this temperature at the start of profile mode." }, { "id": "ProfilePreheatSpeed", "maxLen": 5, "maxLen2": 11, "include": ["PROFILE_SUPPORT"], - "description": "How fast the temperature is allowed to rise during the heatup phase of the soldering profile." + "description": "How fast the temperature is allowed to rise during the preheat phase at the start of profile mode." }, { "id": "ProfilePhase1Temp", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Target temperature for the end of phase 1 of the soldering profile." + "description": "Target temperature for the end of phase 1 of profile mode." }, { "id": "ProfilePhase1Duration", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Duration of phase 1 of the soldering profile. The phase might actually take longer if it takes longer to reach the target temperature." + "description": "Duration of phase 1 of profile mode. The phase might actually take longer if it takes longer to reach the target temperature." }, { "id": "ProfilePhase2Temp", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Target temperature for the end of phase 2 of the soldering profile." + "description": "Target temperature for the end of phase 2 of profile mode." }, { "id": "ProfilePhase2Duration", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Duration of phase 2 of the soldering profile. The phase might actually take longer if it takes longer to reach the target temperature." + "description": "Duration of phase 2 of profile mode. The phase might actually take longer if it takes longer to reach the target temperature." }, { "id": "ProfilePhase3Temp", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Target temperature for the end of phase 3 of the soldering profile." + "description": "Target temperature for the end of phase 3 of profile mode." }, { "id": "ProfilePhase3Duration", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Duration of phase 3 of the soldering profile. The phase might actually take longer if it takes longer to reach the target temperature." + "description": "Duration of phase 3 of profile mode. The phase might actually take longer if it takes longer to reach the target temperature." }, { "id": "ProfilePhase4Temp", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Target temperature for the end of phase 5 of the soldering profile." + "description": "Target temperature for the end of phase 5 of profile mode." }, { "id": "ProfilePhase4Duration", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Duration of phase 5 of the soldering profile. The phase might actually take longer if it takes longer to reach the target temperature." + "description": "Duration of phase 5 of profile mode. The phase might actually take longer if it takes longer to reach the target temperature." }, { "id": "ProfilePhase5Temp", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Target temperature for the end of phase 5 of the soldering profile." + "description": "Target temperature for the end of phase 5 of profile mode." }, { "id": "ProfilePhase5Duration", "maxLen": 4, "maxLen2": 9, "include": ["PROFILE_SUPPORT"], - "description": "Duration of phase 5 of the soldering profile. The phase might actually take longer if it takes longer to reach the target temperature." + "description": "Duration of phase 5 of profile mode. The phase might actually take longer if it takes longer to reach the target temperature." }, { "id": "ProfileCooldownSpeed", "maxLen": 5, "maxLen2": 11, "include": ["PROFILE_SUPPORT"], - "description": "How fast the temperature is allowed to drop after the last phase of the soldering profile." + "description": "How fast the temperature is allowed to drop during the cooldown phase at the end of profile mode." }, { "id": "MotionSensitivity", diff --git a/source/Core/Inc/Settings.h b/source/Core/Inc/Settings.h index be983f73..de969703 100644 --- a/source/Core/Inc/Settings.h +++ b/source/Core/Inc/Settings.h @@ -53,7 +53,7 @@ enum SettingsOptions { CalibrateCJC = 36, // Toggle calibrate CJC at next boot BluetoothLE = 37, // Toggle BLE if present PDVpdo = 38, // Toggle PPS & EPR - ProfilePhases = 39, // Number of Soldering Profile Phases + ProfilePhases = 39, // Number of profile mode phases ProfilePreheatTemp = 40, // Temperature to preheat to before the first phase ProfilePreheatSpeed = 41, // Maximum allowed preheat speed in degrees per second ProfilePhase1Temp = 42, // Temperature to target for the end of phase 1 diff --git a/source/Core/Threads/OperatingModes/HomeScreen.cpp b/source/Core/Threads/OperatingModes/HomeScreen.cpp index fa2388e2..c1ee6854 100644 --- a/source/Core/Threads/OperatingModes/HomeScreen.cpp +++ b/source/Core/Threads/OperatingModes/HomeScreen.cpp @@ -57,7 +57,7 @@ void drawHomeScreen(bool buttonLockout) { case BUTTON_F_LONG: #ifdef PROFILE_SUPPORT if (!isTipDisconnected()) { - gui_solderingProfileMode(); // enter soldering profile mode + gui_solderingProfileMode(); // enter profile mode buttonLockout = true; } #else |