#ifndef CONFIGURATION_H_ #define CONFIGURATION_H_ #include /** * Configuration.h * Define here your default pre settings for Pinecilv2 * */ //=========================================================================== //============================= Default Settings ============================ //=========================================================================== /** * Default soldering temp is 320.0 C * Temperature the iron sleeps at - default 150.0 C */ #define SLEEP_TEMP 150 // Default sleep temperature #define BOOST_TEMP 420 // Default boost temp. #define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable /** * Blink the temperature on the cooling screen when its > 50C */ #define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable /** * How many seconds/minutes we wait until going to sleep/shutdown. * Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds! */ #define SLEEP_TIME 5 // x10 Seconds #define SHUTDOWN_TIME 10 // Minutes /** * Auto start off for safety. * Pissible values are: * 0 - none * 1 - Soldering Temperature * 2 - Sleep Temperature * 3 - Sleep Off Temperature */ #define AUTO_START_MODE 0 // Default to none /** * Locking Mode * When in soldering mode a long press on both keys toggle the lock of the buttons * Possible values are: * 0 - Desactivated * 1 - Lock except boost * 2 - Full lock */ #define LOCKING_MODE 0 // Default to desactivated for safety /** * OLED Orientation * */ #define ORIENTATION_MODE 2 // 0: Right 1:Left 2:Automatic - Default Automatic #define MAX_ORIENTATION_MODE 2 // Up to auto #define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change /** * OLED Brightness * */ #define MIN_BRIGHTNESS 1 // Min OLED brightness selectable #define MAX_BRIGHTNESS 101 // Max OLED brightness selectable #define BRIGHTNESS_STEP 25 // OLED brightness increment #define DEFAULT_BRIGHTNESS 26 // default OLED brightness /** * Temp change settings */ #define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1 #define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10 #define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value #define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value /* Power pulse for keeping power banks awake*/ #define POWER_PULSE_INCREMENT 1 #define POWER_PULSE_MAX 100 // x10 max watts #define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds #define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds #ifdef MODEL_Pinecilv2 #define POWER_PULSE_DEFAULT 0 #else #define POWER_PULSE_DEFAULT 5 #endif /* Pinecil */ #define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s #define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms /** * OLED Orientation Sensitivity on Automatic mode! * Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive> */ #define SENSITIVITY 7 // Default 7 /** * Detailed soldering screen * Detailed idle screen (off for first time users) */ #define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0 #define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0 #define THERMAL_RUNAWAY_TIME_SEC 20 #define THERMAL_RUNAWAY_TEMP_C 20 #define CUT_OUT_SETTING 0 // default to no cut-off voltage #define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33)) #define TEMPERATURE_INF 0 // default to 0 #define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow #define ANIMATION_LOOP 1 // 0: off 1: on #define ANIMATION_SPEED settingOffSpeed_t::MEDIUM #define OP_AMP_Rf_Pinecil 680 * 1000 // 680 Kilo-ohms -> From schematic, R1 #define OP_AMP_Rin_Pinecil 2370 // 2.37 Kilo-ohms -> From schematic, R2 #define OP_AMP_GAIN_STAGE_PINECIL (1 + (OP_AMP_Rf_Pinecil / OP_AMP_Rin_Pinecil)) #if defined(MODEL_Pinecilv2) == 0 #error "No model defined!" #endif #ifdef MODEL_Pinecilv2 #define ADC_VDD_MV 3200 // ADC max reading millivolts #define ADC_MAX_READING ((1 << 16) >> 1) // Maximum reading of the adc #define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C #define VOLTAGE_DIV 630 // 600 - Default divider from schematic #define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV #define MIN_CALIBRATION_OFFSET 100 // Min value for calibration #define PID_POWER_LIMIT 120 // Sets the max pwm power limit #define POWER_LIMIT 0 // 0 watts default limit #define MAX_POWER_LIMIT 120 // Sets the max power limit #define POWER_LIMIT_STEPS 5 // #define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_PINECIL // Uses TS100 resistors #define TEMP_uV_LOOKUP_HAKKO // Use Hakko lookup table #define USB_PD_VMAX 28 // Maximum voltage for PD to negotiate #define PID_TIM_HZ (10) // Tick rate of the PID loop #define MAX_TEMP_C 450 // Max soldering temp selectable °C #define MAX_TEMP_F 850 // Max soldering temp selectable °F #define MIN_TEMP_C 10 // Min soldering temp selectable °C #define MIN_TEMP_F 50 // Min soldering temp selectable °F #define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C #define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F #define DEVICE_HAS_VALIDATION_CODE // We have 2 digit validations #define POW_PD 1 // Supported features #define USB_PD_EPR_WATTAGE 140 // USB PD EPR Wattage #define POW_PD_EXT 0 // Future-proof macro for other models with other PD modes #define POW_QC 1 // Supported features #define POW_DC 1 // Supported features #define POW_QC_20V 1 // Supported features #define POW_EPR 1 #define ENABLE_QC2 1 #define MAG_SLEEP_SUPPORT 1 #define AUTO_TIP_SELECTION 1 // Can auto-select the tip #define TIPTYPE_T12 1 // Can manually pick a T12 tip #define DEVICE_HAS_VALIDATION_SUPPORT #define OLED_96x16 1 #define TEMP_NTC #define ACCEL_BMA #define CUSTOM_MAX_TEMP_C 1 // Uses custom max temp lookup #define ACCEL_SC7 #define HALL_SENSOR #define HALL_SI7210 #define DEBUG_UART_OUTPUT #define HAS_POWER_DEBUG_MENU #define HARDWARE_MAX_WATTAGE_X10 750 #define BLE_ENABLED // We have a BLE stack #define NEEDS_VBUS_PROBE 0 // No vbus probe, its not connected in pcb #define CANT_DIRECT_READ_SETTINGS // We cant memcpy settings due to flash cache #define TIP_CONTROL_PID // We use PID rather than integrator #define TIP_PID_KP 40 // Reasonable compromise for most tips so far #define TIP_PID_KI 6 // About as high for stability across tips #define TIP_PID_KD 200 // Helps dampen smaller tips; ~= nothing for larger tips #define FILTER_DISPLAYED_TIP_TEMP 8 // Filtering for GUI display #endif /* Pinecilv2 */ #define FLASH_PAGE_SIZE (1024) // Read pages // Erase is 4 or 8 k size, so we pad these apart for now // If we ever get low on flash, will need better solution #define FLASH_LOGOADDR (0x23000000 + (1016 * FLASH_PAGE_SIZE)) #define SETTINGS_START_PAGE (1023 * FLASH_PAGE_SIZE) // Hal auto offsets base addr #endif /* CONFIGURATION_H_ */