blob: d56f4f83aaf5b9157a4cb70b0b44193892de3ab4 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
|
#pragma once
/**
* Configuration.h
* Define here your default pre settings for TS80 or TS100
*
*/
//===========================================================================
//============================= Default Settings ============================
//===========================================================================
/**
* Default soldering temp is 320.0 C
* Temperature the iron sleeps at - default 150.0 C
*/
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
#define SLEEP_TEMP 150 // Default sleep temperature
#define BOOST_TEMP 420 // Default boost temp.
#define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable
/**
* Blink the temperature on the cooling screen when its > 50C
*/
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable
/**
* How many seconds/minutes we wait until going to sleep/shutdown.
* Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
*/
#define SLEEP_TIME 5 // x10 Seconds
#define SHUTDOWN_TIME 10 // Minutes
/**
* Auto start off for safety.
* Pissible values are:
* 0 - none
* 1 - Soldering Temperature
* 2 - Sleep Temperature
* 3 - Sleep Off Temperature
*/
#define AUTO_START_MODE 0 // Default to none
/**
* OLED Orientation
*
*/
#define ORIENTATION_MODE 0 // 0: Right 1:Left 2:Automatic - Default right
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperatur change
/**
* Temp change settings
*/
#define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1
#define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
#define TEMP_CHANGE_LONG_STEP_MAX 100 // Temp change long step MAX value
/**
* OLED Orientation Sensitivity on Automatic mode!
* Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
*/
#define SENSITIVITY 7 // Default 7
/**
* Detailed soldering screen
* Detailed idle screen (off for first time users)
*/
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
#define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0
#define CUT_OUT_SETTING 0 // default to no cut-off voltage (or 18W for TS80)
#define TEMPERATURE_INF 0 // default to 0
#define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow
#define POWER_LIMIT_ENABLE 0 // 0: Disable 1: Enable - Default disabled power limit
#ifdef MODEL_TS100
#define VOLTAGE_DIV 467 // 467 - Default divider from schematic
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
#define PID_POWER_LIMIT 70 // Sets the max pwm power limit
#define POWER_LIMIT 30 // 30 watts default limit
#define MAX_POWER_LIMIT 65 //
#define POWER_LIMIT_STEPS 5 //
/**
* TIP_GAIN = TIP_GAIN/1000 == uV per deg C constant of the tip
*/
#define OP_AMP_Rf 750*1000 // 750 Kilo-ohms -> From schematic, R1
#define OP_AMP_Rin 2370 // 2.37 Kilo-ohms -> From schematic, R2
#define TIP_GAIN 405
#endif
#ifdef MODEL_TS80
#define VOLTAGE_DIV 780 // Default divider from schematic
#define PID_POWER_LIMIT 24 // Sets the max pwm power limit
#define CALIBRATION_OFFSET 900 // the adc offset in uV
#define POWER_LIMIT 24 // 24 watts default power limit
#define MAX_POWER_LIMIT 30 //
#define POWER_LIMIT_STEPS 2
/**
* TIP_GAIN = TIP_GAIN/1000 == uV per deg C constant of the tip
*/
#define OP_AMP_Rf 180*1000 // 180 Kilo-ohms -> From schematic, R6
#define OP_AMP_Rin 2000 // 2.0 Kilo-ohms -> From schematic, R3
#define TIP_GAIN 115
#endif
|
