1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
# Tutorial
If this is your first time trying out **Orca**, watch this [introduction video](https://www.youtube.com/watch?v=RaI_TuISSJE). If you're looking for additional examples, visit [this repository](https://git.sr.ht/~rabbits/orca-examples/tree/master/).
## General
- On **OSX**, setup [IAC virtual MIDI buses](https://help.ableton.com/hc/en-us/articles/209774225-Using-virtual-MIDI-buses).
- On **Windows**, setup [loopMidi](http://www.tobias-erichsen.de/software/loopmidi.html).
- On **Linux**, setup [qjacktl](https://qjackctl.sourceforge.io/).
## Pilot
[Pilot](https://github.com/hundredrabbits/Pilot) is a minimalist synth software designed to work via UDP, and to quickly get started with Orca. This **requires no setup**, as long as both applications are open, they should be able to communicate with each other.
- Launch Orca & Pilot.
- In Orca, make sure that UDP is pointing to port `49161`.
- Bang something like `;03Cff` to [play a note](https://github.com/hundredrabbits/pilot#play).
- Bang something like `;revff` to [add reverb](https://github.com/hundredrabbits/pilot#effects).
## Ableton Live
To send [Midi notes](https://github.com/hundredrabbits/Orca#midi) to [Ableton Live](https://www.ableton.com/en/) instruments, bang the Midi operator `:`, like `:03C` to send to _Channel 1, Octave 3, Note C_. Have a look at [midi.orca](hhttps://git.sr.ht/~rabbits/orca-examples/tree/master/basics/_midi.orca) to see it in action.
- Launch Ableton Live.
- Create a new **midi instrument** track.
- Select `IAC Driver(Bus 1)`(OSX), or `LoopMidi`(Windows), in the instrument's inputs dropdown.
- Activate the **In** toggle, on the instrument track.
## SonicPi
To send [OSC messages](https://github.com/hundredrabbits/Orca#osc) to [SonicPi](http://sonic-pi.net), select [port 4560](https://github.com/samaaron/sonic-pi/blob/master/etc/doc/tutorial/12.1-Receiving-OSC.md). SonicPi listens to the address defined in `sync`, to send to the `live_loop`, bang the OSC node `=`, like `=a`. If you need help, visit the [SonicPi x Orca forum](https://in-thread.sonic-pi.net/t/using-orca-to-control-sonic-pi-with-osc/2381/).
```
live_loop :drum do
use_real_time
sync "/osc*/a"
sample :bd_haus, rate: 1
end
```
## Bitwig [Linux and JACK]
The following is taken from this page: https://answers.bitwig.com/questions/1218/how-do-i-get-midi-inout-of-bws-on-linux
- Quit Bitwig if running.
- Start `qjacktl`.
- Go to _Setup > Settings > Parameters_ and set MIDI Driver to "none" (this turns off jack-midi)
- Go to Setup > Misc and check "Enable ALSA Sequencer Support" (if not enabled)
- Stop Jack if running and quit gjackctl
- Run sudo modprobe snd_virmidi midi_devs=1 (to enable virtual midi with one device which is easier to understand for now)
- Start qjacktl
- Start jack
- Open Connections: Connect device on left "0: QuNexus MIDI 1" (as an example) to "0:VirMIDI 5-0"
- Open Bitwig
- Under Options > Preferences > Controllers click "Add controller manually"
- Choose "Generic MIDI Keyboard"
- Once it appears as an input choose "Virtual Raw MIDI/1"
## VCV Rack
- Start VCV Rack
- Add a "VCV MIDI-CV" module to your rack
- Set the first parameter, MIDI Driver, to your local loopback driver
- Windows: Start loopMIDI, be sure to create at least one device, then select "loopMIDI" as the parameter
- Linux: Use "ALSA" (the widely supported Linux sound architecture)
- Set the second parameter to the MIDI interface
- Windows: Use the loopMIDI device you created
- Linux: Select the default "MIDI Through" device (available by default on most ALSA configurations)
- Start Orca
- Use the Hotkey Ctrl+Period to cycle through MIDI output devices until you see your device in the lower-right corner
- Bang a MIDI command to VCV: `:03c88` to get a note and gate trigger from MIDI-CV
## FAQS
### Why does placement of `V` matter?
Orca operates linearly from the top-left, to the bottom-right, operators are executed in that sequence, and so the variables stored at the top, can be overwritten by the variables declared at the bottom.
### Why is orca not making any sound?
Orca is not a synthetizer, it is meant to control audio & visual software, or hardware. Orca will never include domain specific operators to generate music or to create pictures. It is designed to be as generic as possible.
## Golf
### Modulo
Will output the modulo of `6 % 4`.
```
1X.
6I4
```
### Uppercase
Will output uppercase `C`.
```
cA1.
.dAZ
```
### Lowercase
Will output lowercase `C`.
```
H..
CM1
```
### Not Null
Will bang if `L` free input is not null.
```
.L0.
..F0
```
|
