path: root/app/Kconfig

# Copyright (c) 2020 The ZMK Contributors
# SPDX-License-Identifier: MIT

mainmenu "ZMK Firmware"

menu "ZMK"

menu "Basic Keyboard Setup"

config ZMK_KEYBOARD_NAME
    string "Keyboard Name"

config USB_DEVICE_PRODUCT
    default ZMK_KEYBOARD_NAME

config BT_DEVICE_NAME
    default ZMK_KEYBOARD_NAME

config USB_DEVICE_VID
    default 0x1D50

config USB_DEVICE_PID
    default 0x615E

config USB_DEVICE_MANUFACTURER
    default "ZMK Project"

config BT_DIS_PNP_VID
    default 0x1D50

config BT_DIS_PNP_PID
    default 0x615E

config BT_DIS_MODEL
    default ZMK_KEYBOARD_NAME

config BT_DIS_MANUF
    default "ZMK Project"

# Hardware specific overrides

if SOC_SERIES_NRF52X

# Default on for our usage until boards implement retained bootmode.
config NRF_STORE_REBOOT_TYPE_GPREGRET
    bool
    default y

endif # SOC_SERIES_NRF52X

menu "HID"

choice ZMK_HID_REPORT_TYPE
    prompt "HID Report Type"

config ZMK_HID_REPORT_TYPE_HKRO
    bool "#-Key Roll Over (HKRO) HID Report"
    help
      Enable # key roll over for HID report. This selection is "boot keyboard" compatible
      but limits the total number of possible keys to report as held to #.

config ZMK_HID_REPORT_TYPE_NKRO
    bool "Full N-Key Roll Over (NKRO) HID Report"
    help
      Enable full N-Key Roll Over for HID output. This selection will prevent the keyboard
      from working with some BIOS/UEFI versions that only support "boot keyboard" support.
      This option also prevents using some infrequently used higher range HID usages (notably F13-F24 and INTL1-9)
      These usages can be re enabled with ZMK_HID_KEYBOARD_NKRO_EXTENDED_REPORT.

endchoice

config ZMK_HID_KEYBOARD_NKRO_EXTENDED_REPORT
    bool "Enable extended NKRO reporting"
    depends on ZMK_HID_REPORT_TYPE_NKRO
    help
      Enables higher usage range for NKRO (F13-F24 and INTL1-9).
      Please note this is not compatible with Android currently and you will get no input


if ZMK_HID_REPORT_TYPE_HKRO

config ZMK_HID_KEYBOARD_REPORT_SIZE
    int "# Keyboard Keys Reportable"

endif # ZMK_HID_REPORT_TYPE_HKRO

config ZMK_HID_CONSUMER_REPORT_SIZE
    int "# Consumer Keys Reportable"

choice ZMK_HID_CONSUMER_REPORT_USAGES
    prompt "HID Report Type"

config ZMK_HID_CONSUMER_REPORT_USAGES_FULL
    bool "Full Consumer HID Usage Support"
    help
      Enable full Consumer usage ID values to be sent to hosts. Allows for less
      frequently used usages, but has compatibability issues with some host OSes.

config ZMK_HID_CONSUMER_REPORT_USAGES_BASIC
    bool "Basic Consumer HID Usage Support"
    help
      Enable Consumer usage ID values up to "Playback Speed - Slow" to be sent to
      hosts. Allows for broader compatibability with more host OSes.

endchoice

config ZMK_HID_INDICATORS
    bool "HID Indicators"
    help
      Enable HID indicators, used for detecting state of Caps/Scroll/Num Lock,
      Kata, and Compose.

config ZMK_HID_SEPARATE_MOD_RELEASE_REPORT
    bool "Release Modifiers Separately"
    help
      Send a separate release event for the modifiers, to make sure the release
      of the modifier doesn't get recognized before the actual key's release event.

menu "Output Types"

config ZMK_USB
    bool "USB"
    depends on (!ZMK_SPLIT || (ZMK_SPLIT && ZMK_SPLIT_ROLE_CENTRAL))
    select USB
    select USB_DEVICE_STACK
    select USB_DEVICE_HID

config ZMK_USB_BOOT
    bool "USB Boot Protocol Support"
    depends on ZMK_USB
    select USB_HID_BOOT_PROTOCOL
    select USB_DEVICE_SOF

if ZMK_USB

config USB_NUMOF_EP_WRITE_RETRIES
    default 10

config USB_HID_POLL_INTERVAL_MS
    default 1

endif # ZMK_USB

menuconfig ZMK_BLE
    bool "BLE (HID over GATT)"
    select BT
    select BT_SMP
    select BT_SMP_SC_PAIR_ONLY
    select BT_SMP_APP_PAIRING_ACCEPT
    select BT_PERIPHERAL
    select BT_DIS
    imply BT_DEVICE_NAME_DYNAMIC
    imply BT_SETTINGS if !ARCH_POSIX
    imply SETTINGS if !ARCH_POSIX
    imply ZMK_BATTERY_REPORTING if !ARCH_POSIX

if ZMK_BLE

config ZMK_BLE_EXPERIMENTAL_CONN
    bool "Experimental BLE connection changes"
    help
      Enables settings that are planned to be default in future versions of ZMK
      to improve connection stability.

config ZMK_BLE_EXPERIMENTAL_SEC
    bool "Experimental BLE security changes"
    imply BT_SMP_ALLOW_UNAUTH_OVERWRITE
    help
      Enables security settings that are planned to be officially supported in the future.

config ZMK_BLE_EXPERIMENTAL_FEATURES
    bool "Experimental BLE connection and security settings/features"
    select ZMK_BLE_EXPERIMENTAL_CONN
    select ZMK_BLE_EXPERIMENTAL_SEC
    help
      Enables experimental connection changes and security features.

config ZMK_BLE_PASSKEY_ENTRY
    bool "Require passkey entry on the keyboard to complete pairing"
    select RING_BUFFER

config BT_SMP_ALLOW_UNAUTH_OVERWRITE
    imply ZMK_BLE_PASSKEY_ENTRY

config BT_CTLR_PHY_2M
    default n if ZMK_BLE_EXPERIMENTAL_CONN

# BT_TINYCRYPT_ECC is required for BT_SMP_SC_PAIR_ONLY when using HCI
config BT_TINYCRYPT_ECC
    default y if BT_HCI && !BT_CTLR

config SYSTEM_WORKQUEUE_STACK_SIZE
    default 4096 if SOC_RP2040
    default 2048

config ZMK_BLE_THREAD_STACK_SIZE
    int "BLE notify thread stack size"
    default 768

config ZMK_BLE_THREAD_PRIORITY
    int "BLE notify thread priority"
    default 5

config ZMK_BLE_KEYBOARD_REPORT_QUEUE_SIZE
    int "Max number of keyboard HID reports to queue for sending over BLE"
    default 20

config ZMK_BLE_CONSUMER_REPORT_QUEUE_SIZE
    int "Max number of consumer HID reports to queue for sending over BLE"
    default 5

config ZMK_BLE_MOUSE_REPORT_QUEUE_SIZE
    int "Max number of mouse HID reports to queue for sending over BLE"
    default 20

config ZMK_BLE_CLEAR_BONDS_ON_START
    bool "Configuration that clears all bond information from the keyboard on startup."

# HID GATT notifications sent this way are *not* picked up by Linux, and possibly others.
config BT_GATT_NOTIFY_MULTIPLE
    default n

config BT_GATT_AUTO_SEC_REQ
    default (ZMK_SPLIT_BLE && !ZMK_SPLIT_ROLE_CENTRAL)

config BT_DEVICE_APPEARANCE
    default 961

config BT_PERIPHERAL_PREF_MIN_INT
    default 6

config BT_PERIPHERAL_PREF_MAX_INT
    default 12

config BT_PERIPHERAL_PREF_LATENCY
    default 30

config BT_PERIPHERAL_PREF_TIMEOUT
    default 400

endif # ZMK_BLE

endmenu # Output Types

endmenu # HID

rsource "src/split/Kconfig"

endmenu # Basic Keyboard Setup

menu "Keymaps"

config ZMK_KEYMAP_LAYER_REORDERING
    bool "Layer Reordering Support"

config ZMK_KEYMAP_SETTINGS_STORAGE
    bool "Settings Save/Load"
    depends on SETTINGS
    depends on ZMK_BEHAVIOR_LOCAL_IDS

if ZMK_KEYMAP_SETTINGS_STORAGE

config ZMK_KEYMAP_LAYER_NAME_MAX_LEN
    int "Max Layer Name Length"
    default 20

endif # ZMK_KEYMAP_SETTINGS_STORAGE

endmenu # Keymaps

rsource "src/studio/Kconfig"

menu "Display/LED Options"

rsource "src/display/Kconfig"

menuconfig ZMK_RGB_UNDERGLOW
    bool "RGB Addressable LED Underglow"
    select LED_STRIP
    select ZMK_LOW_PRIORITY_WORK_QUEUE

if ZMK_RGB_UNDERGLOW

config ZMK_RGB_UNDERGLOW_EXT_POWER
    bool "RGB underglow toggling also controls external power"

config ZMK_RGB_UNDERGLOW_BRT_MIN
    int "RGB underglow minimum brightness in percent"
    range 0 100

config ZMK_RGB_UNDERGLOW_BRT_MAX
    int "RGB underglow maximum brightness in percent"
    range ZMK_RGB_UNDERGLOW_BRT_MIN 100

config ZMK_RGB_UNDERGLOW_HUE_STEP
    int "RGB underglow hue step in degrees"
    range 0 359

config ZMK_RGB_UNDERGLOW_SAT_STEP
    int "RGB underglow saturation step in percent"
    range 0 100

config ZMK_RGB_UNDERGLOW_BRT_STEP
    int "RGB underglow brightness step in percent"
    range 0 100

config ZMK_RGB_UNDERGLOW_HUE_START
    int "RGB underglow start hue value in degrees"
    range 0 359

config ZMK_RGB_UNDERGLOW_SAT_START
    int "RGB underglow start saturations value in percent"
    range 0 100

config ZMK_RGB_UNDERGLOW_BRT_START
    int "RGB underglow start brightness value in percent"
    range ZMK_RGB_UNDERGLOW_BRT_MIN ZMK_RGB_UNDERGLOW_BRT_MAX

config ZMK_RGB_UNDERGLOW_SPD_START
    int "RGB underglow start animation speed value"
    range 1 5

config ZMK_RGB_UNDERGLOW_EFF_START
    int "RGB underglow start effect int value related to the effect enum list"
    range 0 3

config ZMK_RGB_UNDERGLOW_ON_START
    bool "RGB underglow starts on by default"

config ZMK_RGB_UNDERGLOW_AUTO_OFF_IDLE
    bool "Turn off RGB underglow when keyboard goes into idle state"

config ZMK_RGB_UNDERGLOW_AUTO_OFF_USB
    bool "Turn off RGB underglow when USB is disconnected"
    depends on USB_DEVICE_STACK

endif # ZMK_RGB_UNDERGLOW

menuconfig ZMK_BACKLIGHT
    bool "LED backlight"
    select LED

if ZMK_BACKLIGHT

config ZMK_BACKLIGHT_BRT_STEP
    int "Brightness step in percent"
    range 1 100

config ZMK_BACKLIGHT_BRT_START
    int "Default brightness in percent"
    range 1 100

config ZMK_BACKLIGHT_ON_START
    bool "Default backlight state"

config ZMK_BACKLIGHT_AUTO_OFF_IDLE
    bool "Turn off backlight when keyboard goes into idle state"

config ZMK_BACKLIGHT_AUTO_OFF_USB
    bool "Turn off backlight when USB is disconnected"

endif # ZMK_BACKLIGHT

endmenu # Display/LED Options

rsource "src/pointing/Kconfig"

menu "Power Management"

config ZMK_BATTERY_REPORTING
    bool "Battery level detection/reporting"
    select SENSOR
    select ZMK_LOW_PRIORITY_WORK_QUEUE
    imply BT_BAS if ZMK_BLE

if ZMK_BATTERY_REPORTING

choice ZMK_BATTERY_REPORTING_FETCH_MODE
    prompt "Battery Reporting Fetch Mode"

config ZMK_BATTERY_REPORTING_FETCH_MODE_STATE_OF_CHARGE
    bool "State of charge"

config ZMK_BATTERY_REPORTING_FETCH_MODE_LITHIUM_VOLTAGE
    bool "Lithium Voltage"

endchoice

endif # ZMK_BATTERY_REPORTING

config ZMK_IDLE_TIMEOUT
    int "Milliseconds of inactivity before entering idle state (OLED shutoff, etc)"
    default 30000

config ZMK_SLEEP
    bool "Enable deep sleep support"
    depends on HAS_POWEROFF
    select POWEROFF
    select ZMK_PM_DEVICE_SUSPEND_RESUME
    imply USB

if ZMK_SLEEP

config PM_DEVICE
    default y

config ZMK_IDLE_SLEEP_TIMEOUT
    int "Milliseconds of inactivity before entering deep sleep"
    default 900000

endif # ZMK_SLEEP

config ZMK_EXT_POWER
    bool "Enable support to control external power output"

config ZMK_PM
    bool

config ZMK_PM_DEVICE_SUSPEND_RESUME
    bool
    select ZMK_PM

config ZMK_PM_SOFT_OFF
    bool "Soft-off support"
    depends on HAS_POWEROFF
    select ZMK_PM
    select PM_DEVICE
    select ZMK_PM_DEVICE_SUSPEND_RESUME
    select POWEROFF

config ZMK_GPIO_KEY_WAKEUP_TRIGGER
    bool "Hardware supported wakeup (GPIO)"
    default y
    depends on DT_HAS_ZMK_GPIO_KEY_WAKEUP_TRIGGER_ENABLED && ZMK_PM_SOFT_OFF

# Power Management
endmenu

menu "Combo options"

config ZMK_COMBO_MAX_PRESSED_COMBOS
    int "Maximum number of currently pressed combos"
    default 4

config ZMK_COMBO_MAX_COMBOS_PER_KEY
    int "Maximum number of combos per key"
    default 5

config ZMK_COMBO_MAX_KEYS_PER_COMBO
    int "Maximum number of keys per combo"
    default 4

# Combo options
endmenu

menu "Behavior Options"

config ZMK_BEHAVIORS_QUEUE_SIZE
    int "Maximum number of behaviors to allow queueing from a macro or other complex behavior"
    default 64

rsource "Kconfig.behaviors"

config ZMK_MACRO_DEFAULT_WAIT_MS
    int "Default time to wait (in milliseconds) before triggering the next behavior in macros"
    default 15

config ZMK_MACRO_DEFAULT_TAP_MS
    int "Default time to wait (in milliseconds) between the press and release events of a tapped behavior in macros"
    default 30

endmenu

menu "Advanced"

menu "Initialization Priorities"

if USB_DEVICE_STACK

config ZMK_USB_INIT_PRIORITY
    int "USB Init Priority"
    default 94

config ZMK_USB_HID_INIT_PRIORITY
    int "USB HID Init Priority"
    default 95

endif # USB

if ZMK_BLE || ZMK_SPLIT_BLE

config ZMK_BLE_INIT_PRIORITY
    int "BLE Init Priority"
    default 50

endif # ZMK_BLE || ZMK_SPLIT_BLE

endmenu # Initialization Priorities

menuconfig ZMK_KSCAN
    bool "ZMK KScan Integration"
    default y
    select KSCAN

if ZMK_KSCAN

config ZMK_KSCAN_EVENT_QUEUE_SIZE
    int "Size of the event queue for KSCAN events to buffer events"
    default 4

endif # ZMK_KSCAN

config ZMK_KSCAN_SIDEBAND_BEHAVIORS
    bool
    default y
    depends on DT_HAS_ZMK_KSCAN_SIDEBAND_BEHAVIORS_ENABLED
    select KSCAN

if ZMK_KSCAN_SIDEBAND_BEHAVIORS

config ZMK_KSCAN_SIDEBAND_BEHAVIORS_INIT_PRIORITY
    int "Keyboard scan sideband behaviors driver init priority"
    # The default kscan init priority is 90, so be sure we are initialized later.
    default 95

endif # ZMK_KSCAN_SIDEBAND_BEHAVIORS

menu "Logging"

config ZMK_LOGGING_MINIMAL
    bool "Suppress all ZMK debug log messages"
    default false

if !ZMK_LOGGING_MINIMAL

config ZMK_LOG_LEVEL
    default 4

endif

config ZMK_USB_LOGGING
    bool "Enable USB CDC ACM logging to help debug"
    select LOG
    select USB
    select USB_DEVICE_STACK
    select USB_CDC_ACM
    select SERIAL
    select CONSOLE
    select UART_INTERRUPT_DRIVEN
    select UART_LINE_CTRL
    select UART_CONSOLE
    select USB_UART_CONSOLE

if ZMK_USB_LOGGING

choice USB_CDC_ACM_LOG_LEVEL_CHOICE
    default USB_CDC_ACM_LOG_LEVEL_OFF
endchoice

choice USB_DRIVER_LOG_LEVEL_CHOICE
    default USB_DRIVER_LOG_LEVEL_OFF
endchoice

# We do this to avoid log loop where logging to USB generates more log messages.

config USB_CDC_ACM_RINGBUF_SIZE
    default 1024

config LOG_PROCESS_THREAD_STARTUP_DELAY_MS
    default 1000

endif # ZMK_USB_LOGGING

config ZMK_RTT_LOGGING
    bool "Enable RTT logging to help debug"
    select LOG
    select DEBUG
    select ASSERT
    select USE_SEGGER_RTT
    select CONSOLE
    select RTT_CONSOLE

if ZMK_RTT_LOGGING

config SEGGER_RTT_BUFFER_SIZE_UP
    default 8192

endif # ZMK_RTT_LOGGING

if ZMK_USB_LOGGING || ZMK_RTT_LOGGING

config LOG_BUFFER_SIZE
    default 8192

config LOG_PROCESS_THREAD_SLEEP_MS
    default 100

endif # ZMK_USB_LOGGING || ZMK_RTT_LOGGING

endmenu # Logging

if SETTINGS

config ZMK_SETTINGS_RESET_ON_START
    bool "Delete all persistent settings when the keyboard boots"

if ZMK_SETTINGS_RESET_ON_START

config ZMK_SETTINGS_RESET_ON_START_INIT_PRIORITY
    int "Settings Reset ON Start Initialization Priority"
    default 60
    help
      Initialization priority for the settings reset on start. Must be lower priority/
      higher value than FLASH_INIT_PRIORITY if using the NVS/Flash settings backend.

endif # ZMK_SETTINGS_RESET_ON_START

config ZMK_SETTINGS_SAVE_DEBOUNCE
    int "Milliseconds to debounce settings saves"
    default 60000

endif # SETTINGS

config ZMK_BATTERY_REPORT_INTERVAL
    depends on ZMK_BATTERY_REPORTING
    int "Battery level report interval in seconds"

config ZMK_LOW_PRIORITY_WORK_QUEUE
    bool "Work queue for low priority items"

if ZMK_LOW_PRIORITY_WORK_QUEUE

config ZMK_LOW_PRIORITY_THREAD_STACK_SIZE
    int "Low priority thread stack size"
    default 768

config ZMK_LOW_PRIORITY_THREAD_PRIORITY
    int "Low priority thread priority"
    default 10

endif # ZMK_LOW_PRIORITY_WORK_QUEUE

endmenu # Advanced

endmenu # ZMK

config KERNEL_BIN_NAME
    default "zmk"

config REBOOT
    default y

config USB_DEVICE_STACK
    default y if HAS_HW_NRF_USBD

config FPU
    default CPU_HAS_FPU

config ZMK_WPM
    bool "Calculate WPM"

config ZMK_KEYMAP_SENSORS
    bool "Enable Keymap Sensors support"
    default y
    depends on DT_HAS_ZMK_KEYMAP_SENSORS_ENABLED
    select SENSOR

if ZMK_KEYMAP_SENSORS

config ZMK_KEYMAP_SENSORS_DEFAULT_TRIGGERS_PER_ROTATION
    int "Default triggers per rotation"
    help
      Unless overridden for a sensor in the board/shield/devicetree, this value
      determines how many times to trigger the bound behavior per full rotation.
      For tactile encoders with detents, this usually should match the number of
      detents per rotation of the encoder.
    default 20

endif # ZMK_KEYMAP_SENSORS

choice CBPRINTF_IMPLEMENTATION
    default CBPRINTF_NANO

endchoice

module = ZMK
module-str = zmk
source "subsys/logging/Kconfig.template.log_config"

rsource "boards/Kconfig"
rsource "boards/shields/*/Kconfig.defconfig"
rsource "boards/shields/*/Kconfig.shield"

osource "$(ZMK_CONFIG)/boards/shields/*/Kconfig.defconfig"
osource "$(ZMK_CONFIG)/boards/shields/*/Kconfig.shield"

rsource "Kconfig.defaults"

source "Kconfig.zephyr"