Fomatting and adjust setpoint

6 files changed, 11 insertions, 11 deletions

diff --git a/source/Core/BSP/MHP30/configuration.h b/source/Core/BSP/MHP30/configuration.h
index a2d5910b..8698a857 100644
--- a/source/Core/BSP/MHP30/configuration.h
+++ b/source/Core/BSP/MHP30/configuration.h
@@ -103,8 +103,8 @@
 #define DETAILED_IDLE      0 // 0: Disable 1: Enable - Default 0
 
 // Due to large thermal mass of the PCB being heated we need to pull this back a bit
-#define THERMAL_RUNAWAY_TIME_SEC 45
-#define THERMAL_RUNAWAY_TEMP_C   3
+#define THERMAL_RUNAWAY_TIME_SEC 20
+#define THERMAL_RUNAWAY_TEMP_C   2
 
 #define CUT_OUT_SETTING          0  // default to no cut-off voltage
 #define RECOM_VOL_CELL           33 // Minimum voltage per cell (Recommended 3.3V (33))
diff --git a/source/Core/BSP/Miniware/configuration.h b/source/Core/BSP/Miniware/configuration.h
index 913883e1..c040dece 100644
--- a/source/Core/BSP/Miniware/configuration.h
+++ b/source/Core/BSP/Miniware/configuration.h
@@ -104,7 +104,7 @@
 #define DETAILED_IDLE      0 // 0: Disable 1: Enable - Default 0
 
 #define THERMAL_RUNAWAY_TIME_SEC 20
-#define THERMAL_RUNAWAY_TEMP_C   10
+#define THERMAL_RUNAWAY_TEMP_C   3
 
 #define CUT_OUT_SETTING          0  // default to no cut-off voltage
 #define RECOM_VOL_CELL           33 // Minimum voltage per cell (Recommended 3.3V (33))
diff --git a/source/Core/BSP/Pinecil/configuration.h b/source/Core/BSP/Pinecil/configuration.h
index fe04595b..bef59a93 100644
--- a/source/Core/BSP/Pinecil/configuration.h
+++ b/source/Core/BSP/Pinecil/configuration.h
@@ -104,7 +104,7 @@
 #define DETAILED_IDLE      0 // 0: Disable 1: Enable - Default 0
 
 #define THERMAL_RUNAWAY_TIME_SEC 20
-#define THERMAL_RUNAWAY_TEMP_C   20
+#define THERMAL_RUNAWAY_TEMP_C   3
 
 #define CUT_OUT_SETTING          0  // default to no cut-off voltage
 #define RECOM_VOL_CELL           33 // Minimum voltage per cell (Recommended 3.3V (33))
diff --git a/source/Core/BSP/Pinecilv2/configuration.h b/source/Core/BSP/Pinecilv2/configuration.h
index 8ca4ff40..3f7aa52e 100644
--- a/source/Core/BSP/Pinecilv2/configuration.h
+++ b/source/Core/BSP/Pinecilv2/configuration.h
@@ -105,7 +105,7 @@
 #define DETAILED_IDLE      0 // 0: Disable 1: Enable - Default 0
 
 #define THERMAL_RUNAWAY_TIME_SEC 20
-#define THERMAL_RUNAWAY_TEMP_C   20
+#define THERMAL_RUNAWAY_TEMP_C   3
 
 #define CUT_OUT_SETTING          0  // default to no cut-off voltage
 #define RECOM_VOL_CELL           33 // Minimum voltage per cell (Recommended 3.3V (33))
diff --git a/source/Core/BSP/Sequre/configuration.h b/source/Core/BSP/Sequre/configuration.h
index be3c9f6b..df06f68e 100644
--- a/source/Core/BSP/Sequre/configuration.h
+++ b/source/Core/BSP/Sequre/configuration.h
@@ -133,7 +133,7 @@
 #define TEMP_uV_LOOKUP_S60
 #define USB_PD_VMAX              12 // Maximum voltage for PD to negotiate
 #define THERMAL_RUNAWAY_TIME_SEC 20
-#define THERMAL_RUNAWAY_TEMP_C   10
+#define THERMAL_RUNAWAY_TEMP_C   3
 
 #define HARDWARE_MAX_WATTAGE_X10 600
 
@@ -167,7 +167,7 @@
 #define TEMP_uV_LOOKUP_S60
 #define USB_PD_VMAX              20 // Maximum voltage for PD to negotiate
 #define THERMAL_RUNAWAY_TIME_SEC 20
-#define THERMAL_RUNAWAY_TEMP_C   10
+#define THERMAL_RUNAWAY_TEMP_C   3
 
 #define HARDWARE_MAX_WATTAGE_X10 600
 
@@ -218,8 +218,8 @@
 
 #define TIP_THERMAL_MASS         30 // X10 watts to raise 1 deg C in 1 second
 #define TIP_THERMAL_INERTIA      10 // We use a large inertia value to smooth out the drive to the tip since its stupidly sensitive
-#define THERMAL_RUNAWAY_TIME_SEC 60
-#define THERMAL_RUNAWAY_TEMP_C   3
+#define THERMAL_RUNAWAY_TIME_SEC 30
+#define THERMAL_RUNAWAY_TEMP_C   2
 
 #define COPPER_HEATER_COIL 1  // Have a heater coil that changes resistance on us
 #define TIP_RESISTANCE     52 // PCB heater, measured at ~19C. Will shift by temp a decent amount
diff --git a/source/Core/Threads/PIDThread.cpp b/source/Core/Threads/PIDThread.cpp
index 4927bb47..b928692c 100644
--- a/source/Core/Threads/PIDThread.cpp
+++ b/source/Core/Threads/PIDThread.cpp
@@ -30,7 +30,7 @@ int32_t                    powerSupplyWattageLimit = 0;
 bool                       heaterThermalRunaway    = false;

 

 static int32_t getPIDResultX10Watts(TemperatureType_t set_point, TemperatureType_t current_value);

-static void detectThermalRunaway(const TemperatureType_t currentTipTempInC, const uint32_t x10WattsOut) ;

+static void    detectThermalRunaway(const TemperatureType_t currentTipTempInC, const uint32_t x10WattsOut);

 static void    setOutputx10WattsViaFilters(int32_t x10Watts);

 static int32_t getX10WattageLimits();

 

@@ -93,7 +93,7 @@ void startPIDTask(void const *argument __unused) {
         }

 

         x10WattsOut = getPIDResultX10Watts(PIDTempTarget, currentTipTempInC);

-        detectThermalRunaway(currentTipTempInC,x10WattsOut);

+        detectThermalRunaway(currentTipTempInC, x10WattsOut);

       } else {

         detectThermalRunaway(currentTipTempInC, 0);

       }