diff options
Diffstat (limited to 'source/Core/BSP')
-rw-r--r-- | source/Core/BSP/MHP30/configuration.h | 4 | ||||
-rw-r--r-- | source/Core/BSP/Miniware/configuration.h | 2 | ||||
-rw-r--r-- | source/Core/BSP/Pinecil/configuration.h | 2 | ||||
-rw-r--r-- | source/Core/BSP/Pinecilv2/configuration.h | 2 | ||||
-rw-r--r-- | source/Core/BSP/Sequre/configuration.h | 8 |
5 files changed, 9 insertions, 9 deletions
diff --git a/source/Core/BSP/MHP30/configuration.h b/source/Core/BSP/MHP30/configuration.h index a2d5910b..8698a857 100644 --- a/source/Core/BSP/MHP30/configuration.h +++ b/source/Core/BSP/MHP30/configuration.h @@ -103,8 +103,8 @@ #define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0 // Due to large thermal mass of the PCB being heated we need to pull this back a bit -#define THERMAL_RUNAWAY_TIME_SEC 45 -#define THERMAL_RUNAWAY_TEMP_C 3 +#define THERMAL_RUNAWAY_TIME_SEC 20 +#define THERMAL_RUNAWAY_TEMP_C 2 #define CUT_OUT_SETTING 0 // default to no cut-off voltage #define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33)) diff --git a/source/Core/BSP/Miniware/configuration.h b/source/Core/BSP/Miniware/configuration.h index a873bcc4..44ef5d66 100644 --- a/source/Core/BSP/Miniware/configuration.h +++ b/source/Core/BSP/Miniware/configuration.h @@ -109,7 +109,7 @@ #define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0 #define THERMAL_RUNAWAY_TIME_SEC 20 -#define THERMAL_RUNAWAY_TEMP_C 10 +#define THERMAL_RUNAWAY_TEMP_C 3 #define CUT_OUT_SETTING 0 // default to no cut-off voltage #define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33)) diff --git a/source/Core/BSP/Pinecil/configuration.h b/source/Core/BSP/Pinecil/configuration.h index fe04595b..bef59a93 100644 --- a/source/Core/BSP/Pinecil/configuration.h +++ b/source/Core/BSP/Pinecil/configuration.h @@ -104,7 +104,7 @@ #define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0 #define THERMAL_RUNAWAY_TIME_SEC 20 -#define THERMAL_RUNAWAY_TEMP_C 20 +#define THERMAL_RUNAWAY_TEMP_C 3 #define CUT_OUT_SETTING 0 // default to no cut-off voltage #define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33)) diff --git a/source/Core/BSP/Pinecilv2/configuration.h b/source/Core/BSP/Pinecilv2/configuration.h index 8ca4ff40..3f7aa52e 100644 --- a/source/Core/BSP/Pinecilv2/configuration.h +++ b/source/Core/BSP/Pinecilv2/configuration.h @@ -105,7 +105,7 @@ #define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0 #define THERMAL_RUNAWAY_TIME_SEC 20 -#define THERMAL_RUNAWAY_TEMP_C 20 +#define THERMAL_RUNAWAY_TEMP_C 3 #define CUT_OUT_SETTING 0 // default to no cut-off voltage #define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33)) diff --git a/source/Core/BSP/Sequre/configuration.h b/source/Core/BSP/Sequre/configuration.h index be3c9f6b..df06f68e 100644 --- a/source/Core/BSP/Sequre/configuration.h +++ b/source/Core/BSP/Sequre/configuration.h @@ -133,7 +133,7 @@ #define TEMP_uV_LOOKUP_S60 #define USB_PD_VMAX 12 // Maximum voltage for PD to negotiate #define THERMAL_RUNAWAY_TIME_SEC 20 -#define THERMAL_RUNAWAY_TEMP_C 10 +#define THERMAL_RUNAWAY_TEMP_C 3 #define HARDWARE_MAX_WATTAGE_X10 600 @@ -167,7 +167,7 @@ #define TEMP_uV_LOOKUP_S60 #define USB_PD_VMAX 20 // Maximum voltage for PD to negotiate #define THERMAL_RUNAWAY_TIME_SEC 20 -#define THERMAL_RUNAWAY_TEMP_C 10 +#define THERMAL_RUNAWAY_TEMP_C 3 #define HARDWARE_MAX_WATTAGE_X10 600 @@ -218,8 +218,8 @@ #define TIP_THERMAL_MASS 30 // X10 watts to raise 1 deg C in 1 second #define TIP_THERMAL_INERTIA 10 // We use a large inertia value to smooth out the drive to the tip since its stupidly sensitive -#define THERMAL_RUNAWAY_TIME_SEC 60 -#define THERMAL_RUNAWAY_TEMP_C 3 +#define THERMAL_RUNAWAY_TIME_SEC 30 +#define THERMAL_RUNAWAY_TEMP_C 2 #define COPPER_HEATER_COIL 1 // Have a heater coil that changes resistance on us #define TIP_RESISTANCE 52 // PCB heater, measured at ~19C. Will shift by temp a decent amount |