path: root/source/Core/BSP/Miniware/configuration.h

#ifndef CONFIGURATION_H_
#define CONFIGURATION_H_
#include <stdint.h>
/**
 * Configuration.h
 * Define here your default pre settings for TS80(P) or TS10(0/1)
 *
 */

//===========================================================================
//============================= Default Settings ============================
//===========================================================================
/**
 * Default soldering temp is 320.0 C
 * Temperature the iron sleeps at - default 150.0 C
 */

#define SLEEP_TEMP         150 // Default sleep temperature
#define BOOST_TEMP         420 // Default boost temp.
#define BOOST_MODE_ENABLED 1   // 0: Disable 1: Enable

/**
 * Blink the temperature on the cooling screen when its > 50C
 */
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable

/**
 * How many seconds/minutes we wait until going to sleep/shutdown.
 * Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
 */
#define SLEEP_TIME    5  // x10 Seconds
#define SHUTDOWN_TIME 10 // Minutes

/**
 * Auto start off for safety.
 * Pissible values are:
 *  0 - none
 *  1 - Soldering Temperature
 *  2 - Sleep Temperature
 *  3 - Sleep Off Temperature
 */
#define AUTO_START_MODE 0 // Default to none

/**
 * Locking Mode
 * When in soldering mode a long press on both keys toggle the lock of the buttons
 * Possible values are:
 *  0 - Desactivated
 *  1 - Lock except boost
 *  2 - Full lock
 */
#define LOCKING_MODE 0 // Default to desactivated for safety

/**
 * OLED Orientation
 *
 */
#define ORIENTATION_MODE           2 // 0: Right 1:Left 2:Automatic - Default Automatic
#define MAX_ORIENTATION_MODE       2 // Up to auto
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change

/**
 * OLED Brightness
 *
 */
#if defined(MODEL_TS101)
  #define MIN_BRIGHTNESS     1   // Min OLED brightness selectable
  #define MAX_BRIGHTNESS     101 // Max OLED brightness selectable
#else
  #define MIN_BRIGHTNESS     0   // Min OLED brightness selectable
  #define MAX_BRIGHTNESS     100 // Max OLED brightness selectable
#endif
#define BRIGHTNESS_STEP    25  // OLED brightness increment
#define DEFAULT_BRIGHTNESS 25  // default OLED brightness

/**
 * Temp change settings
 */
#define TEMP_CHANGE_SHORT_STEP     1  // Default temp change short step +1
#define TEMP_CHANGE_LONG_STEP      10 // Default temp change long step +10
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
#define TEMP_CHANGE_LONG_STEP_MAX  90 // Temp change long step MAX value

/* Power pulse for keeping power banks awake*/
#define POWER_PULSE_INCREMENT    1
#define POWER_PULSE_MAX          100 // x10 max watts
#define POWER_PULSE_WAIT_MAX     9   // 9*2.5s = 22.5 seconds
#define POWER_PULSE_DURATION_MAX 9   // 9*250ms = 2.25 seconds

#ifdef MODEL_TS100
#define POWER_PULSE_DEFAULT 0
#else
#define POWER_PULSE_DEFAULT 5
#endif                                 /* TS100 */
#define POWER_PULSE_WAIT_DEFAULT     4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms

/**
 * OLED Orientation Sensitivity on Automatic mode!
 * Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
 */
#define SENSITIVITY 7 // Default 7

/**
 * Detailed soldering screen
 * Detailed idle screen (off for first time users)
 */
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
#define DETAILED_IDLE      0 // 0: Disable 1: Enable - Default 0

#define THERMAL_RUNAWAY_TIME_SEC 20
#define THERMAL_RUNAWAY_TEMP_C   3

#define CUT_OUT_SETTING          0  // default to no cut-off voltage
#define RECOM_VOL_CELL           33 // Minimum voltage per cell (Recommended 3.3V (33))
#define TEMPERATURE_INF          0  // default to 0
#define DESCRIPTION_SCROLL_SPEED 0  // 0: Slow 1: Fast - default to slow
#define ANIMATION_LOOP           1  // 0: off 1: on
#define ANIMATION_SPEED          settingOffSpeed_t::MEDIUM

#define OP_AMP_Rf_TS100  750 * 1000 // 750  Kilo-ohms -> From schematic, R1
#define OP_AMP_Rin_TS100 2370       // 2.37 Kilo-ohms -> From schematic, R2

#define OP_AMP_GAIN_STAGE_TS100 (1 + (OP_AMP_Rf_TS100 / OP_AMP_Rin_TS100))

#define OP_AMP_Rf_TS80  180 * 1000 //  180  Kilo-ohms -> From schematic, R6
#define OP_AMP_Rin_TS80 2000       //  2.0  Kilo-ohms -> From schematic, R3

#define OP_AMP_GAIN_STAGE_TS80 (1 + (OP_AMP_Rf_TS80 / OP_AMP_Rin_TS80))

#define ADC_MAX_READING (4096 * 8) // Maximum reading of the adc
#define ADC_VDD_MV      3300       // ADC max reading millivolts

#define POW_PD_EXT 0

// Deriving the Voltage div:
// Vin_max = (3.3*(r1+r2))/(r2)
// vdiv = (32768*4)/(vin_max*10)

#if defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) + defined(MODEL_TS101) > 1
#error "Multiple models defined!"
#elif defined(MODEL_TS100) + defined(MODEL_TS80) + defined(MODEL_TS80P) + defined(MODEL_TS101) == 0
#error "No model defined!"
#endif
#define NEEDS_VBUS_PROBE 0
// Miniware is swapping IMU's around a bit now, so we turn them all on

#define ACCEL_MMA
#define ACCEL_LIS
#define ACCEL_SC7
#define ACCEL_MSA
#define ACCEL_BMA

#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
#define SOLDERING_TEMP         320 // Default soldering temp is 320.0 °C
#define PID_TIM_HZ             (8) // Tick rate of the PID loop
#define MAX_TEMP_C             450 // Max soldering temp selectable °C
#define MAX_TEMP_F             850 // Max soldering temp selectable °F
#define MIN_TEMP_C             10  // Min soldering temp selectable °C
#define MIN_TEMP_F             50  // Min soldering temp selectable °F
#define MIN_BOOST_TEMP_C       250 // The min settable temp for boost mode °C
#define MIN_BOOST_TEMP_F       480 // The min settable temp for boost mode °F

// Miniware cant be trusted, and keep using the GD32 randomly now, so assume they will clones in the future

#define I2C_SOFT_BUS_1 1

#ifdef MODEL_TS100
#define VOLTAGE_DIV        467 // 467 - Default divider from schematic
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
#define PID_POWER_LIMIT    70  // Sets the max pwm power limit
#define POWER_LIMIT        0   // 0 watts default limit
#define MAX_POWER_LIMIT    70
#define POWER_LIMIT_STEPS  5
#define OP_AMP_GAIN_STAGE  OP_AMP_GAIN_STAGE_TS100
#define TEMP_uV_LOOKUP_HAKKO
#define USB_PD_VMAX              20 // Maximum voltage for PD to negotiate
#define OLED_I2CBB1              1
#define ACCEL_I2CBB1             1
#define HARDWARE_MAX_WATTAGE_X10 750
#define TIP_THERMAL_MASS         65 // X10 watts to raise 1 deg C in 1 second
#define TIP_RESISTANCE           75 // x10 ohms, 7.5 typical for ts100 tips

#define POW_DC
#define I2C_SOFT_BUS_1 1
#define OLED_I2CBB1    1
#define ACCEL_I2CBB1   1
#define TIPTYPE_T12    1 // Can manually pick a T12 tip

#define TEMP_TMP36
#endif /* TS100 */

#ifdef MODEL_TS101
#define VOLTAGE_DIV        700 // 700 - Default divider from schematic
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
#define PID_POWER_LIMIT    100 // Sets the max pwm power limit
#define POWER_LIMIT        0   // 0 watts default limit
#define MAX_POWER_LIMIT    100
#define POWER_LIMIT_STEPS  5
#define OP_AMP_GAIN_STAGE  OP_AMP_GAIN_STAGE_TS100
#define TEMP_uV_LOOKUP_HAKKO
#define ACCEL_LIS_CLONE          1
#define HARDWARE_MAX_WATTAGE_X10 1000
#define TIP_THERMAL_MASS         65 // X10 watts to raise 1 deg C in 1 second
#define TIP_RESISTANCE           75 // x10 ohms, 7.5 typical for ts100 tips

#define TIP_HAS_DIRECT_PWM   1
#define POW_DC               1
#define POW_PD               1
#define USB_PD_EPR_WATTAGE   140 /* EPR Supported */
#define I2C_SOFT_BUS_2       1
#define OLED_I2CBB1          1
#define USB_PD_I2CBB2        1
#define USB_PD_VMAX          28 // Device supposedly can do 28V; looks like vmax is 33 ish
#define OLED_128x32          1
#define OLED_FLIP            1
#define HAS_SPLIT_POWER_PATH 1
#define TEMP_NTC             1
#define ACCEL_I2CBB1         1
#define POW_EPR              1
#define AUTO_TIP_SELECTION   1 // Can auto-select the tip
#define TIPTYPE_T12          1 // Can manually pick a T12 tip
#define HAS_POWER_DEBUG_MENU
#define DEBUG_POWER_MENU_BUTTON_B

#endif /* TS101 */

#if defined(MODEL_TS80) + defined(MODEL_TS80P) > 0
#define MAX_POWER_LIMIT   40
#define POWER_LIMIT_STEPS 2
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_TS80
#define TEMP_uV_LOOKUP_TS80
#define USB_PD_VMAX 12 // Maximum voltage for PD to negotiate

#define TIP_THERMAL_MASS 40
#define TIP_RESISTANCE   45 // x10 ohms, 4.5 typical for ts80 tips
#define I2C_SOFT_BUS_2   1
#define LIS_ORI_FLIP
#define OLED_FLIP
#define TIPTYPE_TS80 1 // Only one tip type so far

#endif /* TS80(P) */

#ifdef MODEL_TS80
#define VOLTAGE_DIV        780 // Default divider from schematic
#define CALIBRATION_OFFSET 900 // the adc offset in uV
#define PID_POWER_LIMIT    35  // Sets the max pwm power limit
#define POWER_LIMIT        32  // 24 watts default power limit
#define OLED_I2CBB1        1
#define ACCEL_I2CBB1       1

#define HARDWARE_MAX_WATTAGE_X10 320

#define POW_QC

#define TEMP_TMP36
#define I2C_SOFT_BUS_1 1
#define OLED_I2CBB1    1
#define ACCEL_I2CBB1   1
#endif /* TS80 */

#ifdef MODEL_TS80P
#define VOLTAGE_DIV              650  // Default for TS80P with slightly different resistors
#define CALIBRATION_OFFSET       1500 // the adc offset in uV
#define PID_POWER_LIMIT          35   // Sets the max pwm power limit
#define POWER_LIMIT              32   // 30 watts default power limit
#define I2C_SOFT_BUS_2           1
#define HARDWARE_MAX_WATTAGE_X10 320
#define OLED_I2CBB1              1
#define ACCEL_I2CBB1             1

#define POW_PD             1
#define USB_PD_EPR_WATTAGE 0 /*No EPR*/
#define POW_QC             1
#define TEMP_NTC
#define I2C_SOFT_BUS_2 1
#define I2C_SOFT_BUS_1 1
#define OLED_I2CBB1    1
#define ACCEL_I2CBB1   1
#define SC7_ORI_FLIP
#endif /* TS80P */

#ifdef MODEL_TS101
// For whatever reason, Miniware decided to not build a reliable DFU bootloader
// It can't appear to flash to some of the upper pages of flash,
// I'm slightly suspect a watchdog or something runs out
// as device resets before file finishes copying
// So logo has to be located on page 99 or else it cant be flashed on stock bootloader
#define FLASH_LOGOADDR      (0x08000000 + (99 * 1024))
#define SETTINGS_START_PAGE (0x08000000 + (127 * 1024))
#else
#define FLASH_LOGOADDR      (0x08000000 + (62 * 1024))
#define SETTINGS_START_PAGE (0x08000000 + (63 * 1024))
#define OLED_96x16          1
#endif /* TS101 */

#endif /* CONFIGURATION_H_ */