aboutsummaryrefslogtreecommitdiffhomepage
path: root/source/Core/BSP/Pinecil/configuration.h
blob: bef59a9346a651983c1f619a8b07e7e89f819242 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
#ifndef CONFIGURATION_H_
#define CONFIGURATION_H_
#include <stdint.h>
/**
 * Configuration.h
 * Define here your default pre settings for Pinecil
 *
 */

//===========================================================================
//============================= Default Settings ============================
//===========================================================================
/**
 * Default soldering temp is 320.0 C
 * Temperature the iron sleeps at - default 150.0 C
 */

#define SLEEP_TEMP         150 // Default sleep temperature
#define BOOST_TEMP         420 // Default boost temp.
#define BOOST_MODE_ENABLED 1   // 0: Disable 1: Enable

/**
 * Blink the temperature on the cooling screen when its > 50C
 */
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable

/**
 * How many seconds/minutes we wait until going to sleep/shutdown.
 * Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
 */
#define SLEEP_TIME    5  // x10 Seconds
#define SHUTDOWN_TIME 10 // Minutes

/**
 * Auto start off for safety.
 * Pissible values are:
 *  0 - none
 *  1 - Soldering Temperature
 *  2 - Sleep Temperature
 *  3 - Sleep Off Temperature
 */
#define AUTO_START_MODE 0 // Default to none

/**
 * Locking Mode
 * When in soldering mode a long press on both keys toggle the lock of the buttons
 * Possible values are:
 *  0 - Desactivated
 *  1 - Lock except boost
 *  2 - Full lock
 */
#define LOCKING_MODE 0 // Default to desactivated for safety

/**
 * OLED Orientation
 *
 */
#define ORIENTATION_MODE           2 // 0: Right 1:Left 2:Automatic - Default Automatic
#define MAX_ORIENTATION_MODE       2 // Up to auto
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change

/**
 * OLED Brightness
 *
 */
#define MIN_BRIGHTNESS     0   // Min OLED brightness selectable
#define MAX_BRIGHTNESS     100 // Max OLED brightness selectable
#define BRIGHTNESS_STEP    25  // OLED brightness increment
#define DEFAULT_BRIGHTNESS 25  // default OLED brightness

/**
 * Temp change settings
 */
#define TEMP_CHANGE_SHORT_STEP     1  // Default temp change short step +1
#define TEMP_CHANGE_LONG_STEP      10 // Default temp change long step +10
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
#define TEMP_CHANGE_LONG_STEP_MAX  90 // Temp change long step MAX value

/* Power pulse for keeping power banks awake*/
#define POWER_PULSE_INCREMENT    1
#define POWER_PULSE_MAX          100 // x10 max watts
#define POWER_PULSE_WAIT_MAX     9   // 9*2.5s = 22.5 seconds
#define POWER_PULSE_DURATION_MAX 9   // 9*250ms = 2.25 seconds

#ifdef MODEL_Pinecil
#define POWER_PULSE_DEFAULT 0
#else
#define POWER_PULSE_DEFAULT 5
#endif                                 /* Pinecil */
#define POWER_PULSE_WAIT_DEFAULT     4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms

/**
 * OLED Orientation Sensitivity on Automatic mode!
 * Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
 */
#define SENSITIVITY 7 // Default 7

/**
 * Detailed soldering screen
 * Detailed idle screen (off for first time users)
 */
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
#define DETAILED_IDLE      0 // 0: Disable 1: Enable - Default 0

#define THERMAL_RUNAWAY_TIME_SEC 20
#define THERMAL_RUNAWAY_TEMP_C   3

#define CUT_OUT_SETTING          0  // default to no cut-off voltage
#define RECOM_VOL_CELL           33 // Minimum voltage per cell (Recommended 3.3V (33))
#define TEMPERATURE_INF          0  // default to 0
#define DESCRIPTION_SCROLL_SPEED 0  // 0: Slow 1: Fast - default to slow
#define ANIMATION_LOOP           1  // 0: off 1: on
#define ANIMATION_SPEED          settingOffSpeed_t::MEDIUM

#define OP_AMP_Rf_Pinecil  750 * 1000 // 750  Kilo-ohms -> From schematic, R1
#define OP_AMP_Rin_Pinecil 2370       // 2.37 Kilo-ohms -> From schematic, R2

#define OP_AMP_GAIN_STAGE_PINECIL (1 + (OP_AMP_Rf_Pinecil / OP_AMP_Rin_Pinecil))

#define ADC_MAX_READING (4096 * 8) // Maximum reading of the adc
#define ADC_VDD_MV      3300       // ADC max reading millivolts

#if defined(MODEL_Pinecil) == 0
#error "No model defined!"
#endif

#ifdef MODEL_Pinecil
#define SOLDERING_TEMP         320                       // Default soldering temp is 320.0 °C
#define VOLTAGE_DIV            467                       // 467 - Default divider from schematic
#define CALIBRATION_OFFSET     900                       // 900 - Default adc offset in uV
#define MIN_CALIBRATION_OFFSET 100                       // Min value for calibration
#define PID_POWER_LIMIT        70                        // Sets the max pwm power limit
#define POWER_LIMIT            0                         // 0 watts default limit
#define MAX_POWER_LIMIT        70                        //
#define POWER_LIMIT_STEPS      5                         //
#define OP_AMP_GAIN_STAGE      OP_AMP_GAIN_STAGE_PINECIL // Uses TS100 resistors
#define TEMP_uV_LOOKUP_HAKKO                             // Use Hakko lookup table
#define USB_PD_VMAX            20                        // Maximum voltage for PD to negotiate
#define PID_TIM_HZ             (8)                       // Tick rate of the PID loop
#define MAX_TEMP_C             450                       // Max soldering temp selectable °C
#define MAX_TEMP_F             850                       // Max soldering temp selectable °F
#define MIN_TEMP_C             10                        // Min soldering temp selectable °C
#define MIN_TEMP_F             50                        // Min soldering temp selectable °F
#define MIN_BOOST_TEMP_C       250                       // The min settable temp for boost mode °C
#define MIN_BOOST_TEMP_F       480                       // The min settable temp for boost mode °F

#define OLED_96x16         1
#define POW_PD             1
#define USB_PD_EPR_WATTAGE 0 /*No EPR (Yet?) */
#define POW_PD_EXT         0
#define POW_QC             1
#define POW_DC             1
#define POW_QC_20V         1
#define ENABLE_QC2         1
#define MAG_SLEEP_SUPPORT  1
#define TIPTYPE_T12        1 // Can manually pick a T12 tip
#define TEMP_TMP36
#define ACCEL_BMA
#define ACCEL_SC7
#define HALL_SENSOR
#define VBUS_MOD_TEST
#define HALL_SI7210
#define DEBUG_UART_OUTPUT
#define NEEDS_VBUS_PROBE 1

#define HARDWARE_MAX_WATTAGE_X10 750
#define TIP_THERMAL_MASS         65 // X10 watts to raise 1 deg C in 1 second
#define TIP_RESISTANCE           75 // x10 ohms, 7.5 typical for Pinecil tips
#define CANT_DIRECT_READ_SETTINGS
#endif /* Pinecil */

#define FLASH_LOGOADDR      (0x08000000 + (126 * 1024))
#define SETTINGS_START_PAGE (0x08000000 + (127 * 1024))

#define HAS_POWER_DEBUG_MENU

#endif /* CONFIGURATION_H_ */