path: root/Cart_Reader/7800.ino

//******************************************
// ATARI 7800 MODULE
//******************************************
#ifdef ENABLE_7800
// Atari 7800
// Cartridge Pinout
// 32P 2.54mm pitch (USE 36P CONNECTOR)
//
//              RIGHT
//            +-------+
//       R/W -|  1 32 |- CLK
//      HALT -|  2 31 |- IRQ
//            |-------|
//        D3 -|  3 30 |- GND
// L      D4 -|  4 29 |- D2     B
// A      D5 -|  5 28 |- D1     O
// B      D6 -|  6 27 |- D0     T
// E      D7 -|  7 26 |- A0     T
// L     A12 -|  8 25 |- A1     O
//       A10 -|  9 24 |- A2     M
// S     A11 -| 10 23 |- A3
// I      A9 -| 11 22 |- A4     S
// D      A8 -| 12 21 |- A5     I
// E     +5V -| 13 20 |- A6     D
//       GND -| 14 19 |- A7     E
//            |-------|
//       A13 -| 15 18 |- AUD
//       A14 -| 16 17 |- A15
//            +-------+
//              LEFT
//
//                                     LABEL SIDE
//
//         A14 A13  GND +5V  A8  A9 A11 A10 A12  D7  D6  D5  D4  D3  HLT R/W
//       +--------------------------------------------------------------------+
//       |  16  15 | 14  13  12  11  10   9   8   7   6   5   4   3 |  2   1  |
// LEFT  |         |                                                |         | RIGHT
//       |  17  18 | 19  20  21  22  23  24  25  26  27  28  29  30 | 31  32  |
//       +--------------------------------------------------------------------+
//         A15 AUD   A7  A6  A5  A4  A3  A2  A1  A0  D0  D1  D2 GND  IRQ CLK
//
//                                    BOTTOM SIDE

// CONTROL PINS:
// CLK(PH1) - SNES CPUCLK
// R/W(PH6) - SNES /RD
// HALT(PH0) - SNES /RESET

//******************************************
//  Supported Mappers
//******************************************
// Supported Mapper Array
// Format = {mapper,romsizelo,romsizehi}
static const byte PROGMEM a7800mapsize[] = {
  0, 0, 2,  // Standard 16K/32K/48K [7816/7832/7848]
  1, 4, 4,  // SuperGame 128K [78SG]
  2, 5, 5,  // SuperGame - Alien Brigade/Crossbow 144K [78S9]
  3, 3, 3,  // F-18 Hornet 64K [78AB]
  4, 4, 4,  // Double Dragon/Rampage 128K [78AC]
  5, 3, 3,  // Realsports Baseball/Tank Command/Tower Toppler/Waterski 64K [78S4]
  6, 3, 3,  // Karateka (PAL) 64K [78S4 Variant]
  7, 1, 4,  // Bankset switching
};

byte a7800mapcount = 8;  // (sizeof(a7800mapsize) / sizeof(a7800mapsize[0])) / 3;
byte a7800mapselect;
int a7800index;

byte a7800[] = { 16, 32, 48, 64, 128, 144 };
byte a7800lo = 0;  // Lowest Entry
byte a7800hi = 5;  // Highest Entry
byte a7800mapper = 0;
byte a7800size;

// EEPROM MAPPING
// 07 MAPPER
// 08 ROM SIZE

//******************************************
//  Menu
//******************************************
// Base Menu
static const char* const menuOptions7800[] PROGMEM = { FSTRING_SELECT_CART, FSTRING_READ_ROM, FSTRING_SET_SIZE, FSTRING_RESET };

void setup_7800() {
  // Request 5V
  setVoltage(VOLTS_SET_5V);

  // Set Address Pins to Output
  // Atari 7800 uses A0-A15 [A16-A23 UNUSED]
  //A0-A7
  DDRF = 0xFF;
  //A8-A15
  DDRK = 0xFF;
  //A16-A23
  DDRL = 0xFF;

  // Set Control Pins to Output
  //       HALT(PH0)  ---(PH3)   ---(PH4)   ---(PH5)   R/W(PH6)
  DDRH |= (1 << 0) | (1 << 3) | (1 << 4) | (1 << 5) | (1 << 6);

  // Set TIME(PJ0) to Output (UNUSED)
  DDRJ |= (1 << 0);

  // Set Pins (D0-D7) to Input
  DDRC = 0x00;

  // Setting Control Pins to HIGH
  //       HALT(PH0)   ---(PH3)   ---(PH4)   ---(PH5)   R/W(PH6)
  PORTH |= (1 << 0) | (1 << 3) | (1 << 4) | (1 << 5) | (1 << 6);

  // Set Unused Data Pins (PA0-PA7) to Output
  DDRA = 0xFF;

  // Set Unused Pins HIGH
  PORTA = 0xFF;
  PORTL = 0xFF;       // A16-A23
  PORTJ |= (1 << 0);  // TIME(PJ0)

#ifdef ENABLE_CLOCKGEN
  // Adafruit Clock Generator

  initializeClockOffset();

  if (!i2c_found) {
    display_Clear();
    print_FatalError(F("Clock Generator not found"));
  }

  // Set Eeprom clock to 1Mhz
  clockgen.set_freq(200000000ULL, SI5351_CLK1);

  // Start outputting Eeprom clock
  clockgen.output_enable(SI5351_CLK1, 1);  // Eeprom clock

  // Wait for clock generator
  clockgen.update_status();

#else
  // Set CLK(PH1) to Output 
  DDRH |= (1 << 1);
  // Output a high signal CLK(PH1)
  PORTH |= (1 << 1);
#endif

  checkStatus_7800();
  strcpy(romName, "ATARI");

  mode = CORE_7800;
}

void a7800Menu() {
  convertPgm(menuOptions7800, 4);
  uint8_t mainMenu = question_box(F("ATARI 7800 MENU"), menuOptions, 4, 0);

  switch (mainMenu) {
    case 0:
      // Select Cart
      setCart_7800();
      setup_7800();
      break;

    case 1:
      // Read ROM
      sd.chdir("/");
      readROM_7800();
      sd.chdir("/");
      break;

    case 2:
      // Set Mapper + Size
      setMapper_7800();
      checkMapperSize_7800();
      setROMSize_7800();
      break;

    case 3:
      // reset
      resetArduino();
      break;
  }
}

//******************************************
// READ CODE
//******************************************

uint8_t readData_7800(uint16_t addr)  // Add Input Pullup
{
  PORTF = addr & 0xFF;         // A0-A7
  PORTK = (addr >> 8) & 0xFF;  // A8-A15
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  //  DDRC = 0x00; // Set to Input
  PORTC = 0xFF;  // Input Pullup
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  uint8_t ret = PINC;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  return ret;
}

void readSegment_7800(uint16_t startaddr, uint32_t endaddr) {
  for (uint32_t addr = startaddr; addr < endaddr; addr += 512) {
    for (int w = 0; w < 512; w++) {
      uint8_t temp = readData_7800(addr + w);
      sdBuffer[w] = temp;
    }
    myFile.write(sdBuffer, 512);
  }
}

void readSegmentBank_7800(uint8_t startbank, uint8_t endbank) {
  for (uint8_t x = startbank; x < endbank; x++) {
    writeData_7800(0x8000, x);
    readSegment_7800(0x8000, 0xC000);
  }
}

void readStandard_7800() {
  if (a7800size > 1)
    readSegment_7800(0x4000, 0x8000); // +16K = 48K
  if (a7800size > 0)
    readSegment_7800(0x8000, 0xC000); // +16K = 32K
  // Base 16K
  readSegment_7800(0xC000, 0x10000);  // 16K
}

void readSupergame_7800() {
  readSegmentBank_7800(0, 7);         // Bank 0-6 16K * 7 = 112K
  readSegment_7800(0xC000, 0x10000);  // Bank 7  +16K = 128K
}


void writeData_7800(uint16_t addr, uint8_t data) {
  PORTF = addr & 0xFF;         // A0-A7
  PORTK = (addr >> 8) & 0xFF;  // A8-A15
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  DDRC = 0xFF;  // Set to Output
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  PORTC = data;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  PORTH &= ~(1 << 6);  // R/W(PH6) LOW = WRITE
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  PORTH |= (1 << 6);  // R/W(PH6) HIGH = READ
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  DDRC = 0x00;  // Reset to Input
}

// Activision Bankswitch - Double Dragon/Rampage 128K
void bankSwitch_7800(uint16_t addr) {
  PORTF = addr & 0xFF;         // A0-A7
  PORTK = (addr >> 8) & 0xFF;  // A8-A15
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;

  PORTH &= ~(1 << 6);            // R/W(PH6) LOW = WRITE
  for (int y = 0; y < 8; y++) {  // Pulse Clock to latch data into PAL16 Chip
    PORTH &= ~(1 << 1);          // CLK(PH1) LOW
    NOP;
    PORTH |= (1 << 1);  // CLK(PH1) HIGH
    NOP;
  }

  PORTH |= (1 << 6);  // R/W(PH6) HIGH = READ

  DDRC = 0x00;  // Reset to Input
}

//******************************************
// READ ROM
//******************************************

void readROM_7800() {
  createFolderAndOpenFile("7800", "ROM", romName, "a78");

  switch (a7800mapper) {
    case 0:  // Standard 16K/32K/48K [7816/7832/7848]
      readStandard_7800();
      break;

    case 1:  // SuperGame 128K [78SG]
      readSupergame_7800();
      break;

    case 2:                              // SuperGame - Alien Brigade/Crossbow 144K [78S9]
      readSegment_7800(0x4000, 0x8000);  // 16K
      readSegmentBank_7800(0, 8);        // 16K * 8 = +128K = 144K
      break;

    case 3:                                // F-18 Hornet 64K [78AB]
      for (int x = 1; x >= 0; x--) {       // Bank Order Inverted = Bank 1 then Bank 0
        writeData_7800(0x8000, x);         // Banks 0-1
        readSegment_7800(0x4000, 0x8000);  // 16K * 2 = 32K
      }
      readSegment_7800(0x8000, 0x10000);  // +32K = 64K
      break;

    case 4:  // Double Dragon/Rampage 128K [78AC]
      /*
        // THIS CODE OUTPUTS ROMS THAT SHOULD MATCH THE CURRENT NO-INTRO DATABASE
        // BUT THE ROMS INCLUDED IN THE NO-INTRO DATABASE WERE DONE INCORRECTLY
        // THE UPPER AND LOWER HALVES OF EACH 16K BANK ARE IN THE WRONG ORDER
        // THE OLD BANKSWITCH INFORMATION IS INCORRECT/INCOMPLETE
        // Double Dragon (NTSC) = CRC32 AA265865 BAD
        // Double Dragon (PAL)  = CRC32 F29ABDB2 BAD
        // Rampage (NTSC)       = CRC32 39A316AA BAD
        for (int x = 0; x < 8; x++) {
        bankSwitch_7800(0xFF80 + x); // Activision Bankswitch
        readSegment_7800(0xA000, 0xE000); // 16K * 8 = 128K
        }
      */
      // THIS CODE OUTPUTS PROPER ROMS THAT SHOULD MATCH MAME
      // THE UPPER AND LOWER HALVES OF EACH 16K BANK ARE IN THE CORRECT ORDER
      // Double Dragon (NTSC) = CRC32 F20773D5
      // Double Dragon (PAL)  = CRC32 4D634BF5
      // Rampage (NTSC)       = CRC32 D2876EE2
      for (int x = 0; x < 8; x++) {
        bankSwitch_7800(0xFF80 + x);       // Activision Bankswitch
        readSegment_7800(0xC000, 0xE000);  // 8K * 8 = 64K
        readSegment_7800(0xA000, 0xC000);  // 8K * 8 = +64K = 128K
      }
      break;

    case 5:  // Realsports Baseball/Tank Command/Tower Toppler/Waterski 64K [78S4]
      readSegmentBank_7800(0, 4); // 16K * 4 = 64K
      break;

    case 6:  // Karateka (PAL) 64K [78S4 Variant]
      readSegmentBank_7800(4, 8); // 16K * 4 = 64K
      break;

    case 7: // Bankset switching
      if (a7800size > 3) {
        setHalt_7800(1);
        readSupergame_7800();
        setHalt_7800(0);
        readSupergame_7800();
      } else {
        setHalt_7800(1);
        readStandard_7800();
        setHalt_7800(0);
        readStandard_7800();
      }
      break;
  }
  myFile.close();

  printCRC(fileName, NULL, 0);

  println_Msg(FS(FSTRING_EMPTY));
  // Prints string out of the common strings array either with or without newline
  print_STR(press_button_STR, 1);
  display_Update();
  wait();
}

void setHalt_7800(byte on) {
  if(on == 1) {
    PORTH |= (1 << 0);  // HALT(PH0) HIGH = SALLY
  } else {
    PORTH &= ~(1 << 0); // HALT(PH0) LOW = MARIA
  }
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
  NOP;
}

//******************************************
// ROM SIZE
//******************************************

void checkMapperSize_7800() {
  for (int i = 0; i < a7800mapcount; i++) {
    a7800index = i * 3;
    byte mapcheck = pgm_read_byte(a7800mapsize + a7800index);
    if (mapcheck == a7800mapper) {
      a7800lo = pgm_read_byte(a7800mapsize + a7800index + 1);
      a7800hi = pgm_read_byte(a7800mapsize + a7800index + 2);
      break;
    }
  }
}

#if (defined(ENABLE_OLED) || defined(ENABLE_LCD))
void println_Mapper7800(byte mapper) {
  if (mapper == 0)
    println_Msg(F("STANDARD"));
  else if (mapper == 1)
    println_Msg(F("SUPERGAME 128K[78SG]"));
  else if (mapper == 2)
    println_Msg(F("SUPERGAME 144K[78S9]"));
  else if (mapper == 3)
    println_Msg(F("F-18 HORNET   [78AB]"));
  else if (mapper == 4)
    println_Msg(F("DBLDRGN/RMPG  [78AC]"));
  else if (mapper == 5)
    println_Msg(F("BASEBALL/ETC  [78S4]"));
  else if (mapper == 6)
    println_Msg(F("KARATEKA(PAL) [78S4]"));
  else if (mapper == 7)
    println_Msg(F("BANKSET"));
}

void printRomSize_7800(int index) {
    display_Clear();
    print_Msg(F("ROM Size: "));
    println_Msg(a7800[index]);
}
#endif

void setROMSize_7800() {
  byte new7800size;
#if (defined(ENABLE_OLED) || defined(ENABLE_LCD))
  display_Clear();
  if (a7800lo == a7800hi)
    new7800size = a7800lo;
  else {
    display_Clear();

    new7800size = navigateMenu(a7800lo, a7800hi, &printRomSize_7800);
    display.setCursor(0, 56);  // Display selection at bottom
  }
  print_Msg(FS(FSTRING_ROM_SIZE));
  print_Msg(a7800[new7800size]);
  println_Msg(F("K"));
  display_Update();
  delay(1000);
#else
  if (a7800lo == a7800hi)
    new7800size = a7800lo;
  else {
setrom:
    String sizeROM;
    for (int i = 0; i < (a7800hi - a7800lo + 1); i++) {
      Serial.print(F("Select ROM Size:  "));
      Serial.print(i);
      Serial.print(F(" = "));
      Serial.print(a7800[i + a7800lo]);
      Serial.println(F("K"));
    }
    Serial.print(F("Enter ROM Size: "));
    while (Serial.available() == 0) {}
    sizeROM = Serial.readStringUntil('\n');
    Serial.println(sizeROM);
    new7800size = sizeROM.toInt() + a7800lo;
    if (new7800size > a7800hi) {
      Serial.println(F("SIZE NOT SUPPORTED"));
      Serial.println(FS(FSTRING_EMPTY));
      goto setrom;
    }
  }
  Serial.print(F("ROM Size = "));
  Serial.print(a7800[new7800size]);
  Serial.println(F("K"));
#endif
  EEPROM_writeAnything(8, new7800size);
  a7800size = new7800size;
}

void checkStatus_7800() {
  EEPROM_readAnything(7, a7800mapper);
  EEPROM_readAnything(8, a7800size);
  if (a7800mapper > 7) {
    a7800mapper = 0;  // default
    EEPROM_writeAnything(7, a7800mapper);
  }
  if (a7800size > 5) {
    a7800size = 0;  // default 16KB
    EEPROM_writeAnything(8, a7800size);
  }

#if (defined(ENABLE_OLED) || defined(ENABLE_LCD))
  display_Clear();
  println_Msg(F("ATARI 7800 READER"));
  println_Msg(FS(FSTRING_CURRENT_SETTINGS));
  println_Msg(FS(FSTRING_EMPTY));
  print_Msg(F("MAPPER:   "));
  println_Msg(a7800mapper);
  println_Mapper7800(a7800mapper);
  print_Msg(FS(FSTRING_ROM_SIZE));
  print_Msg(a7800[a7800size]);
  println_Msg(F("K"));
  display_Update();
  wait();
#else
  Serial.print(F("MAPPER:   "));
  Serial.println(a7800mapper);
  if (a7800mapper == 0)
    Serial.println(F("Standard [7816/7832/7848]"));
  else if (a7800mapper == 1)
    Serial.println(F("SuperGame 128K [78SG]"));
  else if (a7800mapper == 2)
    Serial.println(F("SuperGame 144K [78S9] - Alien Brigade/Crossbow"));
  else if (a7800mapper == 3)
    Serial.println(F("F-18 Hornet 64K [78AB]"));
  else if (a7800mapper == 4)
    Serial.println(F("Double Dragon/Rampage [78AC]"));
  else if (a7800mapper == 5)
    Serial.println(F("Realsports Baseball/Tank Command/Tower Toppler/Waterski [78S4]"));
  else if (a7800mapper == 6)
    Serial.println(F("Karateka (PAL) [78S4 Variant]"));
  else if (a7800mapper == 7)
    Serial.println(F("Bankset"));
  Serial.print(FS(FSTRING_ROM_SIZE));
  Serial.print(A7800[a7800size]);
  Serial.println(F("K"));
  Serial.println(FS(FSTRING_EMPTY));
#endif
}

//******************************************
// SET MAPPER
//******************************************

#if (defined(ENABLE_OLED) || defined(ENABLE_LCD))
void printMapperSelection_7800(int index) {
  display_Clear();
  print_Msg(FS(FSTRING_MAPPER));
  a7800index = index * 3;
  a7800mapselect = pgm_read_byte(a7800mapsize + a7800index);
  println_Msg(a7800mapselect);
  println_Mapper7800(a7800mapselect);
}
#endif

void setMapper_7800() {
  byte new7800mapper = 0;
#if (defined(ENABLE_OLED) || defined(ENABLE_LCD))
  navigateMenu(0, a7800mapcount - 1, &printMapperSelection_7800);
  new7800mapper = a7800mapselect;

  display.setCursor(0, 56);
  print_Msg(F("MAPPER "));
  print_Msg(new7800mapper);
  println_Msg(F(" SELECTED"));
  display_Update();
  delay(1000);
#else
setmapper:
  String newmap;
  Serial.println(F("SUPPORTED MAPPERS:"));
  Serial.println(F("0 = Standard [7816/7832/7848]"));
  Serial.println(F("1 = SuperGame 128K [78SG]"));
  Serial.println(F("2 = SuperGame 144K [78S9] - Alien Brigade/Crossbow"));
  Serial.println(F("3 = F-18 Hornet 64K [78AB]"));
  Serial.println(F("4 = Double Dragon/Rampage [78AC]"));
  Serial.println(F("5 = Realsports Baseball/Tank Command/Tower Toppler/Waterski [78S4]"));
  Serial.println(F("6 = Karateka (PAL) [78S4 Variant]"));
  Serial.println(F("7 = Bankset"));
  Serial.print(F("Enter Mapper [0-7]: "));
  while (Serial.available() == 0) {}
  newmap = Serial.readStringUntil('\n');
  Serial.println(newmap);
  a7800index = newmap.toInt() * 3;
  new7800mapper = pgm_read_byte(a7800mapsize + a7800index);
#endif
  EEPROM_writeAnything(7, new7800mapper);
  a7800mapper = new7800mapper;

  a7800size = pgm_read_byte(a7800mapsize + a7800index + 1);
  EEPROM_writeAnything(8, a7800size);
}

//******************************************
// CART SELECT CODE
//******************************************

void setCart_7800() {
  //go to root
  sd.chdir();

  struct database_entry_mapper_size entry;

  // Select starting letter
  byte myLetter = starting_letter();

  // Open database
  if (myFile.open("7800.txt", O_READ)) {
    seek_first_letter_in_database(myFile, myLetter);

    if(checkCartSelection(myFile, &readDataLineMapperSize, &entry)) {
      EEPROM_writeAnything(7, entry.gameMapper);
      EEPROM_writeAnything(8, entry.gameSize);
    }
  } else {
    print_FatalError(FS(FSTRING_DATABASE_FILE_NOT_FOUND));
  }
}
#endif